Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 67 | Manualshive

Page: 67 / 1058

background image

6. 802.1X Commands

68

6.12. config 802.1x authorization attributes

radius



Description

This command is used to enable or disable the acceptation of an authorized

configuration. (To configure that attributes, regarding VLAN, 802.1p, ACL and

Ingress/Egress Bandwidth, please refer to the Appendix section at the end of this

document.)



Format

config 802.1x authorization attributes radius [enable | disable]



Parameters



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.



Example

To configure the 802.1X state of acceptation of an authorized configuration:

Zxxx0:admin# config 802.1x auth_parameter ports 1-20 direction both
Command: config 802.1x auth_parameter ports 1-20 direction both

Success.

Zxxx0:admin#

enable

The authorization attributes such as VLAN, 802.1p default priority, and ACL assigned by
the RADUIS server will be accepted if the global authorization status is enabled. The
default state is enabled.

disable

The authorization attributes assigned by the RADUIS server will not be accepted.

Zxxx0:admin#config 802.1x authorization attributes radius enable
Command: config 802.1x authorization attributes radius enable

Success.

Zxxx0:admin#

«
...
65
66
67
68
69
...
»

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZEQUO 6400

Brand: D-Link Pages: 16

Brand: D-Link Pages: 2

QuantaMesh T1048-LB9

Brand: QCT Pages: 42

Brand: Watt Stopper Pages: 10

Brand: AsGa Pages: 23

Brand: Topex Pages: 170

LMX-1002G-SFP Series

Brand: ANTAIRA Pages: 22

Brand: Scion-Tech Pages: 9

Brand: Maestro Pages: 2

LANPLEX 2500 EXTENDEDPLEX 2500 EXTENDED

Brand: 3Com Pages: 186

Brand: Radiient Pages: 4

OmniView F1D066

Brand: Belkin Pages: 12

e labs CAT5TX/RX

Brand: Cable Electronics Pages: 2

Brand: Raritan Pages: 2

Brand: HeroSpeed Pages: 2

Brand: SC&T Pages: 7

Brand: Zamel Pages: 2

Brand: Rose electronics Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands