Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 904

Page: 904 / 1058

78. Subnet VLAN Commands

905

78.5. show vlan_precedence ports



Description

This command is used to display the VLAN classification precedence.



Format

show vlan_precedence ports {<portlist>}



Parameters



Restrictions

None.



Example

To display VLAN classification precedence on ports 1-5:

<portlist>(Optional) Specifies the list of ports used for this display.

Zxxx0:admin#show vlan_precedence ports 1:1-1:5
Command: show vlan_precedence ports 1:1-1:5

Port VLAN Precedence
---- -----------------
1     MAC-Based VLAN
2     Subnet VLAN
3     MAC-Based VLAN
4     MAC-Based VLAN
5     Subnet VLAN

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands