Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 11

Page: 11 / 1058

1. Product Outline



Policy-based routing is supported, allowing for routing according to the access condi

tions.



The Access Control function is supported, allowing to filter by IP address, MAC

address, protocol number, and L4 port number.



VRRP is supported, allowing for layer-3 Switching Hub redundancy.



Spanning Tree Protocol is supported, allowing to build a redundant system.



IEEE802.1Q tagged VLAN is supported, allowing to register up to 4094 VLANs.



The IEEE802.1p QoS function is supported.



The IEEE802.3ad Link Aggregation function is supported, allowing to configure up to 8

ports and 48 groups.



The IEEE802.1X authentication function is supported, allowing to block network access

from unregistered users.



The IGMP Snooping function is supported, allowing to prevent multicast packets

from monopolizing bandwidth.



The Ring Redundant Protocol (RRP) is supported, allowing to make a redundant

network via ring topology.

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands