Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 42

Page: 42 / 1058

5. Basic Management Commands



Restrictions

Only Administrator and Operator-level users can issue this command.



Example

To configure the baud rate:

5.14. enable clipaging



Description

This command is used to enable pausing of the screen display when show command

output reaches the end of the page. The default setting is enabled.



Format

enable clipaging



Parameters

None.



Restrictions

Only Administrator and Operator-level users can issue this command.



Example

Only Administrator and Operator-level users can issue this command.

Zxxx0:admin# config serial_port baud_rate 9600
Command: config serial_port baud_rate 9600

Success.

Zxxx0:admin#

Zxxx0:admin#enable clipaging
Command: enable clipaging

Success.

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands