Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 156

Page: 156 / 1058

12. Basic IP Commands

157

12.1. config ipif



Description

Configure the parameters for an L3 interface. For IPv4, only the system interface can

be specified for the way to get the IP address. If the mode is set to BOOTP or DHCP,

then the IPv4 address will be obtained through the operation of protocols. The

manual configuration of the IP address will be of no use. If the mode is configured to

BOOTP or DHCP first, and then the user configures IP address later, the mode will be

changed to manual configured mode. For IPv6, multiple addresses can be defined on

the same L3 interface. For IPv4, multi-netting must be done by creation of a

secondary interface. Note that an IPv6 address is not allowed to be configured on a

secondary interface.



Format

config ipif <ipif_name 12> [{ipaddress <network_address> | vlan <vlan_name 32> |

state [enable | disable]} | bootp | dhcp | proxy_arp [enable | disable] {local [enable |

disable]} | ipv6 [ipv6address <ipv6networkaddr> | state [enable | disable]] | ip_mtu

ip_directed_broadcast [enable | disable]]



Parameters

ipif

Specifies the IP interface configured.
<ipif_name 12>

Enter the name of the IP interface used here. This name can be up to 12 characters
long. The default interface is 'System'.

ipaddress(Optional) The IP address and netmask of the IP interface to be created.

<network_address>

Specify the address and mask information using the traditional format (for
example, 10.1.2.3/255.0.0.0 or in CIDR format, 10.1.2.3/8).

vlan

(Optional) The name of the VLAN corresponding to the IP interface.
<vlan_name 32>

Specify the VLAN name. The maximum length is 32 characters.

state

Enable or disable the IP interface.
enable

Enable the IP interface.

disable

Disable the IP interface.

bootp

Enable or disable the BOOTP client to get the IP address.

dhcp

Enable or disable the DHCP client to get the IP address.

proxy_arp

(Optional) Enable or disable the proxy ARP. This is for the IPv4 function. The default is
disabled.
enable

Enable the proxy ARP.

disable

Disable the proxy ARP.

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands