Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 501 | Manualshive

Page: 501 / 1058

background image

46. LLDP Commands

502



Example

To display LLDP:

46.5. config lldp forward_message



Description

This command is used to configure LLDP forwarding messages. When LLDP is disabled

and LLDP forward message is enabled, the received LLDPDU packet will be

forwarded. The default state is disabled.



Format

config lldp forward_message [enable | disable]



Parameters



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.

Zxxx0:admin#show lldp
Command: show lldp

LLDP System Information
  Chassis ID Subtype    : MAC Address
  Chassis ID        : 00-11-22-33-44-55
  System Name         :
  System Description    : Gigabit Ethernet Switch
  System Capabilities     : Repeater, Bridge

LLDP Configurations
  LLDP Status         : Disabled
  LLDP Forward Status     : Disabled
  Message TX Interval     : 30
  Message TX Hold Multiplier: 4
  ReInit Delay        : 2
  TX Delay         : 2
  Notification Interval     : 5

Zxxx0:admin#

enable

Enable LLDP forwarding messages.

disable

Disable LLDP forwarding messages.

«
...
499
500
501
502
503
...
»

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZEQUO 6400

ePowerSwitch 8M+R2

Brand: Neol Pages: 74

Brand: Eaton Pages: 40

ETHERNET Accessories 852 852-0111

Brand: WAGO Pages: 38

CN8000 KVM on the NET

Brand: ATEN Pages: 2

Brand: Aethra Pages: 1

Brand: Grozone Control Pages: 20

Brand: Micrel Pages: 15

Brand: KinAn Pages: 4

Brand: N-Tron Pages: 196

EXT-UHDA-HBTL-RX

Brand: Gefen Pages: 33

Brand: Cabletron Systems Pages: 110

Brand: CableTronix Pages: 4

Brand: Ubiquiti Pages: 14

Brand: cable matters Pages: 8

PICO-GUARD SFI-D1EDPXT6

Brand: Banner Pages: 2

Brand: Black Box Pages: 3

Brand: S+S Pages: 16

8 PORT SMART SWITCH CE 232D4SS8

Brand: B&B Electronics Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands