Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 170

Page: 170 / 1058

13. Bootup Function Commands

171

13.Bootup Function Commands

13.1. show boot_file



Description

Use this command to show the boot file.

Bootup Firmware/Configuration cannot be changed forever.

The 2

Bootup Firmware can be set by command "config firmware image

<pathname> boot_up". The 2

Bootup Configuration can be set by command

"config configuration <pathname> boot_up".

Actual Bootup Firmware/Configuration is shown the current actual boot up

firmware and configuration.

If don't input <pathname> for save command, the configuration will be saved to

the 2

Bootup Configuration path and if this path is not exist, the save command

will be fail and print prompt message.



Format

show boot_file



Parameters

None.



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.

show boot_file
config boot_up command

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands