Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 316

Page: 316 / 1058

25. DHCPv6 Relay Command List

317



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.



Example

To configure the maximum hops of a DHCPv6 relay packet could be transferred to 4:

25.4. config dhcpv6_relay



Description

The command could add/delete an IPv6 address which is a destination to forward

(relay) DHCPv6 packets.



Format

config dhcpv6_relay [add | delete] ipif <ipif_name 12> <ipv6addr>



Parameters



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.



Example

To add a DHCPv6 server to the relay table:

Zxxx0:admin# config dhcpv6_relay hop_count 4
Command: config dhcpv6_relay hop_count 4

Success.

Zxxx0:admin#

add

Add an IPv6 destination to the DHCPv6 relay table.

delete

Delete an IPv6 destination from the DHCPv6 relay table

ipif

The name of the IP interface in which DHCPv6 relay is to be enabled.
<ipif_name 12>

Enter the IP interface name here. This name can be up to 12 characters long.

The DHCPv6 server IP address.

Zxxx0:admin# config dhcpv6_relay add ipif System

2001:DB8:1234:0:218:FEFF:FEFB:CC0E
Command: config dhcpv6_relay add ipif System 2001:DB8:1234:0:218:FEFF:FEFB:CC0E

Success.

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands