Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 850

Page: 850 / 1058

73. SNMPv1/v2/v3 Commands

851



Restrictions

Only Administrator-level users can issue this command.



Example

To create a new SNMP group:

73.15. delete snmp group



Description

This command is used to remove an SNMP group.



Format

delete snmp group <groupname 32>

Specify the most secure of the possible security models. Specifies authentication of a
packet.

noauth_nopriv

Specify to neither support packet authentication nor encrypting.

auth_nopriv

Specify to support packet authentication.

auth_priv

Specify to support packet authentication and encrypting.

read_view

Specify the view name between 1 and 32 characters.
<view_name 32>

Specify the view name between 1 and 32 characters.

write_view

Specify the view name between 1 and 32 characters.
<view_name 32>

Specify the view name between 1 and 32 characters.

notify_view

Specify the view name between 1 and 32 characters.
<view_name 32>

Specify the view name between 1 and 32 characters.

Zxxx0:admin#create snmp group MANAGER_group v3 auth_priv read_view

CommunityViewwrite_view CommunityView notify_view CommunityView
Command: create snmp group MANAGER_group v3 auth_priv read_view CommunityView

write_view CommunityView notify_view CommunityView

Success.

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands