Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 527

Page: 527 / 1058

47. Loopback Interface Commands

528

47.4. delete loopback ipif



Description

This command is used to delete a loopback interface.



Format

delete loopback ipif [<ipif_name 12> | all]



Parameters



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.



Example

To delete the loopback interface named loopback1:

<ipif_name 12>

Enter the IP interface name used for this configuration here. This name can be up to 12
characters long.

all

Specifies that all the IP loopback interfaces will be deleted.

Zxxx0:admin# delete loopback ipif loopback1
Command: delete loopback ipif loopback1

Success.

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands