Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 157 | Manualshive

Page: 157 / 1058

background image

12. Basic IP Commands

158



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.



Example

To configure the System IP interface:

local

(Optional) This setting controls whether the system provides the proxy reply for the ARP
packets destined for IP addresses located in the same interface as the received interface.
When proxy ARP is enabled for an interface, the system will do the proxy reply for the
ARP packets destined for IP addresses located on a different interface. For ARP packets
destined for IP address located on the same interface, the system will check this setting to
determine whether to reply. The default is disabled.
enable

Enable the local proxy ARP function.

disable

Disable the local proxy ARP function.

ipv6

The following are IPv6-related parameters.
ipv6address

The IPv6 address and subnet prefix of the IPV6 address to be created.
<ipv6networkaddr>

The IPv6 address and subnet prefix of the IPV6 address to be created.

state Enable or disable the IPv6 state of the IP interface.

enable

Enable the IPv6 state of the IP interface.

disable

Disable the IPv6 state of the IP interface.

ip_mtu

Specifies the IP Layer MTU value used.
<value 512-1712>

Enter the IP Layer MTU value used here. The value must be between 512 and 1712.

dhcpv6_client

Specifies the DHCPv6 client state.
enable

Enable the DHCPv6 client.

disable

Disable the DHCPv6 client.

ipv4 state The state of the IPv4 interface.

enable

Enable the IPv4 state of the IP interface.

disable

Disable the IPv4 state of the IP interface.

ip_directed_broadcast

Specifies the IP directed-broadcast state of the interface.
enable

Specifies that the IP directed-broadcast state of the interface will be enabled.

disable

Specifies that the IP directed-broadcast state of the interface will be disabled.

«
...
155
156
157
158
159
...
»

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZEQUO 6400

Brand: Xantech Pages: 2

Brand: PRO SIGNAL Pages: 5

ETHERNET Accessories 852 852-0111

Brand: WAGO Pages: 38

2X2 VGA SWITCHER

Brand: Gefen Pages: 12

Brand: FCI Pages: 12

Brand: Orno Pages: 2

Brand: Vega Pages: 36

Brand: Lantech Pages: 30

Brand: Optex Pages: 2

Brand: Hall Research Technologies Pages: 9

Brand: Harman Pages: 50

Brand: Tabs Pages: 4

SmartSwitch SBU128

Brand: Cabletron Systems Pages: 76

Brand: LEGRAND Pages: 4

Brand: National Instruments Pages: 23

Brand: H3C Pages: 38

PROFINET 4-port

Brand: Helmholz Pages: 20

Brand: Kramer Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands