Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 131

Page: 131 / 1058

8. Access Control List (ACL) Egress Command List

132

The following example displays an egress access profile that supports an entry mask

for each rule:

Rule ID : 1 (auto assign) Port group: 1

Match on
  Source IP    : 10.0.0.2
  Destination IP     : 10.90.90.90
  DSCP        : 25

Action:
Permit

--------------------------------------------------------------------------------
Rule ID : 2 (auto assign) Port group: 1

Match on
  Source IP    : 10.0.0.1
  Destination IP     : 10.90.90.90
  DSCP        : 25

Action:
Permit

Matched Count : 0 packets
================================================================================

Zxxx0:admin#

Zxxx0:admin# show egress_access_profile profile_id 1
Command: show egress_access_profile profile_id 1

Egress Access Profile Table

================================================================================
Profile ID: 1 Profile name: 1 Type: Ethernet

Mask on
Source MAC : FF-FF-FF-FF-FF-FF

Available Hardware Entries : 127
--------------------------------------------------------------------------------
Rule ID : 1 Port group: -

Match on
VLAN ID : 1
Source MAC : 00-00-00-00-00-01

Action:
Permit

================================================================================
Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands