Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 906 | Manualshive

Page: 906 / 1058

background image

79. Switch Port Commands

907

speed

Set port speed for the specified ports.
auto Set port speed to auto negotiation.
capability_advertised

Specifies that the capability will be advertised.
10_half

Set port speed to 10_half.

10_full

Set port speed to 10_full.

100_half

Set port speed to 100_half.

100_full

Set port speed to 100_full.

1000_full

Set port speed to 1000_full. When setting copper port speed to 1000_full,
users should specify master and slave mode in pair for 1000-BASE TX, and
leave the 1000_full without any master or slave setting for fiber.

master

(Optional) Set to master.

slave

(Optional) Set to slave.

auto_negotiation

Specifies that the auto-negotiation option will be configured.
restart_an

Specifies to restart the auto-negotiation process.

remote_fault_advertised

Specifies that the remote fault advertisement option will be configured.
disable

Specifies to disable remote fault advertisement.

offline

Specifies that a local device may indicate Offline prior to powering off,
running  transmitter  tests,  or  removing  the  local  device  from  the  active
configuration. If it is set and detected offline, it will advertise at the next
auto-negotiation. It interacted for 1000Mbps MAUs.

link_fault

Specifies that if set and local device was detected, a Link_Failure condition
indicated by the loss of synchronization, will advertise at the next auto-
negotiation. It interacted for 1000Mbps MAUs.

auto_negotiation_error

Specifies the resolution which precludes operation between a local device
and link partner advertised at the next auto-negotiation. It interacted for
1000Mbps MAUs.

flow_control

Turn on or turn off flow control on one or more ports by setting flow_control to enable or
disable. The default value is disable.
enable

Turn on flow control.

disable

Turn off flow control.

learning Turn on or turn off MAC address learning on one or more ports. The default value is

enable.
enable

Turn on MAC address learning.

disable

Turn off MAC address learning.

«
...
904
905
906
907
908
...
»

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZEQUO 6400

Brand: Contemporary Controls Pages: 4

Brand: Silent Gliss Pages: 4

Brand: G&D Pages: 80

Hi-Speed USB 4-Port Bay Hub

Brand: SIIG Pages: 8

Brand: H3C Pages: 70

ADDERView Secure AVS-4128

Brand: ADDER Pages: 24

Brand: PTN Pages: 44

SUPERHUB QUATTRO

Brand: Manhattan Pages: 2

Brand: BJ Live Pages: 2

Spectrum 2E42-27

Brand: Cabletron Systems Pages: 77

Brand: Whyte Pages: 12

Binary B-200-AVDMATRIX-6X4

Brand: SNAP Pages: 8

Brand: Microsens Pages: 8

WattStopprer RS-150U

Brand: LEGRAND Pages: 6

Mosaic 0 770 30

Brand: LEGRAND Pages: 3

Galion K8/31D20AN-HK

Brand: LEGRAND Pages: 2

Celiane 67 Series

Brand: LEGRAND Pages: 4

Brand: LEGRAND Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands