Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 336

Page: 336 / 1058

27. Distance Vector Multicast Routing Protocol (DVMRP) Commands

337

27.Distance Vector Multicast Routing

Protocol (DVMRP) Commands

Sending data simultaneously to multiple destinations is called

"multicast" and used for music and video distribution.

DVMRP (Distance Vector Multicast Routing Protocol) is one of

multicast routing protocols. It exchanges route information from the

distribution source to the distribution destination with adjacent routers

and manages the shortest route in a routing table like RIP.

Figure 27-1 DVMRP routing

This Switching Hub supports DVMRP version 3 and enables/disables DVMRP for each

interface.

DVMRP does not always have a fast transmission speed. Therefore, it is used in a

relatively low-bandwidth network where some delay is not a problem. If a high

transmission speed is required, consider using other multicast routing protocols such

as PIM (Protocol Independent Multicast routing).

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands