Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 118

Page: 118 / 1058

8. Access Control List (ACL) Egress Command List

119



Parameters

profile_id

Specifies the index of the egress access list profile. The lower the profile ID, the higher the
priority.
<value 1-4>

Enter the profile ID used here. This value must be between 1 and 4.

profile_name

The name of the profile must be specified. The maximum length is 32 characters.
<name 1-32>

Enter the profile name used here. This name can be up to 32 characters long.

ethernet Specifies this is an Ethernet mask.

vlan (Optional) Specifies a VLAN mask.

Enter the VLAN mask used here.

source_mac

(Optional) Specifies the source MAC mask.
<macmask 000000000000-ffffffffffff>

Enter the source MAC mask used here.

destination_mac

(Optional) Specifies the destination MAC mask.
<macmask 000000000000-ffffffffffff>

Enter the destination MAC mask used here.

802.1p

(Optional) Specifies 802.1p priority tag mask.

ethernet_type

(Optional) Specifies the Ethernet type mask.

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands