Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 209

Page: 209 / 1058

19. Didital Diagnostic Monitoring (DDM) Commands

210

19.6. config ddm ports reload threshold



Description

This command is used to reload the DDM threshold configuration. The command reloads

default threshold configuration of special ports. If the ports are link up with optic modules,

all thresholds of those ports will be set to hardware default. If the ports are not optic ports,

or the ports are link down, all thresholds configuration will be clear.



Format

config ddm ports [<portlist> | all] reload_threshold



Parameters



Restrictions

Administrators and operators.



Example

To reload port 21's threshold configuration:

ports

Specifies a range of ports to be configured. (The portlist format: UnitID: port
number).

all

If 'all' parameter is chosen, all optic ports' operating parameters will be configured.

Zxxx0:admin# config ddm ports 21 reload_threshold
Command: config ddm ports 21 reload_threshold

Success.

Zxxx0:admin#

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands