manualshive.com logo in svg

Panasonic ZEQUO 6400, Operating Instructions Manual

The Panasonic ZEQUO 6400 is a cutting-edge device that offers unparalleled performance. With its sleek design and advanced features, this product is a must-have for tech enthusiasts. Enhance your experience by downloading the Operating Instructions Manual for free from manualshive.com, providing you with the essential guidelines to maximize its potential.

Share
Download
background image

53.  MLD Snooping Commands    

575

Restrictions

Only Administrator, Operator and Power-User level users can issue this command.

Example

To configure MLD snooping:

53.2. config mld_snooping rate_limit

Description

This command is used to configure the upper limit per second for ingress MLD control              

packets.

Format

config mld_snooping rate_limit [ports <portlist> | vlanid <vlanid_list>] [<value 1-1000> | 

no_limit]

Parameters

fast_done

Enable or disable the MLD snooping fast leave function. If enabled, the membership is             
immediately removed when the system receive the MLD leave message.
enable

Enable the MLD snooping fast leave function.

disable

Disable the MLD snooping fast leave function.

proxy_reporting

Specifies that the proxy reporting function will be configured.
state Specifies the state of the proxy reporting function.

enableSpecifies that the proxy reporting function will be enabled.
disableSpecifies that the proxy reporting function will be disabled.

source_ip

Specifies the source IPv6 address used.
<ipv6addr>

Enter the source IPv6 address used here.

Zxxx0:admin#config mld_snooping vlan_name default state enable
Command: config mld_snooping vlan_name default state enable

Success.

Zxxx0:admin#

ports

Specify a range of ports to be configured.
<portlist>

Specify a range of ports to be configured.

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZEQUO 6400

3Com Switch 4500 Family Configuration Manual preview
Switch 4500 Family
Brand: 3Com Pages: 742
3Com Switch 7757 Configuration Manual preview
Switch 7757
Brand: 3Com Pages: 940
3Com 4210 Series Release Notes preview
4210 Series
Brand: 3Com Pages: 43
3Com OfficeConnect WX1200 Command Reference Manual preview
OfficeConnect WX1200
Brand: 3Com Pages: 646
Contemporary Controls EISK5-100T/H Installation Manual preview
EISK5-100T/H
Brand: Contemporary Controls Pages: 4
hager TS 204 User Instruction preview
TS 204
Brand: hager Pages: 2
E-LINK LNK-IMC208P-SFP Quick Start Manual preview
LNK-IMC208P-SFP
Brand: E-LINK Pages: 6
Hanwell IKVM-101Plus User Manual preview
IKVM-101Plus
Brand: Hanwell Pages: 109
Olympia TV 150 Quick Start Manual preview
TV 150
Brand: Olympia Pages: 6
Tekmar tekmarNet4 User Switch 480 Data Brochure preview
tekmarNet4 User Switch 480
Brand: Tekmar Pages: 8
PNI CT25WIFI User Manual preview
CT25WIFI
Brand: PNI Pages: 92
Cabletron Systems 6H122-08 User Manual preview
6H122-08
Brand: Cabletron Systems Pages: 170
IOGear GHDMIMS52 Quick Start Manual preview
GHDMIMS52
Brand: IOGear Pages: 1
Dahua DH-PFS3206-4P-120 User Manual preview
DH-PFS3206-4P-120
Brand: Dahua Pages: 19
3onedata ES2010G-2GS User Manual preview
ES2010G-2GS
Brand: 3onedata Pages: 4
enbrighten 58433 Manual preview
58433
Brand: enbrighten Pages: 2
C&H Technologies M218 User Manual preview
M218
Brand: C&H Technologies Pages: 28
Pakedge Device & Software S8Mpdp Quick Start Manual preview
S8Mpdp
Brand: Pakedge Device & Software Pages: 14

Brands by name

Popular brands

Load more brands