Panasonic ZEQUO 6400 Operating Instructions Manual Download Page 551

Page: 551 / 1058

49. MAC-based Access Control Commands

552



Parameters



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.



Example

To disable the log state for MAC-based Access Control:

49.19. config mac_based_access_control trap

state



Description

This command is used to enable or disable the sending of MAC-based Access Control

traps.



Format

config mac_based_access_control trap state [enable | disable]



Parameters



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.

state

Specifies the log state for MAC-based Access Control.
enable

Specifies that the log for MAC-based Access Control will be enabled.

disable

Specifies that the log for MAC-based Access Control will be disabled.

Zxxx0:admin# config mac_based_access_control log state disable
Command: config mac_based_access_control log state disable

Success.

Zxxx0:admin#

state

Specifies the trap state for MAC-based Access Control.
enable

Specifies that the trap state for MAC-based Access Control will be enabled.

disable

Specifies that the trap state for MAC-based Access Control will be disabled.

Summary of Contents for ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands

Panasonic ZEQUO 6400, Operating Instructions Manual

Search results

Summary of Contents for ZEQUO 6400

Reviews:

Related manuals for ZEQUO 6400

Brands by name

Popular brands