G2
P1
P3
P5
P1
P3
P2
P4
P6
P8
P7
G1
G1 LINK / ACT
G2
PWR
PWR1
PWR2
IPS-3082GC
7
5
6
8
P.O.E.
3
1
2
4
Quick Installation Guide
Q
uick
I
nstallation
G
uide
Introduction
PRINTED ON RECYCLED PAPER
is managed redundant ring Ethernet switch with 8x10/100Base-T(X)
IPS-3082GC-24V
ports with 15.4Watts PoE (P.S.E.) function and 2xGigabit combo ports. With completely
support of Ethernet redundancy protocol, O-Ring (recovery time < 10/30ms over 250
units of connection), O-Chain, MRP
and MSTP/RSTP/STP (IEEE 802.1s/w/D)
*NOTE
can protect your mission-critical applications from network interruptions or temporary
malfunctions with its fast recovery technology. Another O-Chain is the revolutionary
network redundancy technology that provides the add-on network redundancy topology
for any backbone network, O-Chain allows multiple redundant network rings of different
redundancy protocols to join and function together as a larger and more robust
compound network topology.
O-Chain providing ease-of-use while maximizing fault-
recovery swiftness, flexibility, compatibility, and cost-effectiveness in one set of network
redundancy topology.
also supports Power over Ethernet, a system
IPS-3082GC-24V
to transmit electrical power, along with data, to remote devices over standard twisted-
pair cable in an Ethernet network. Each
switch had 8X10/100Base-
IPS-3082GC-24V
T(X) 15.4Watts P.S.E. (Power Sourcing Equipment) ports. P.S.E. is a device (switch or
hub for instance) that will provide power in a PoE setup.
supports
IPS-3082GC-24V
DDM (Digital Diagnostic Monitoring) function, which can monitor instantly the status of
electronic voltage, current and temperature. All function of
can be
IPS-3082GC-24V
managed centralized by a powerful windows utility — Open-Vision. In addition, the wide
operating temperature range from -40 to 70 C can satisfy most of operating
o
environment. Therefore, these switches are one of the most reliable choice for highly-
managed and Fiber Ethernet application with PoE function.
Preparation
Before you begin installing the switch, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient:
If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may be
greater than room ambient. Therefore, consideration should be given to
installing the equipment in an environment compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Safety & Warnings
Dimension
Panel Layouts
1. Power LED
2. PWR1 LED
3. PWR2 LED
4. R.M. status LED
5. Ring status LED
6. Faulty relay indicator
7. Console port
8. Link/Act LED for Gigabit port
9. 100Mbps indicator for Gigabit port
10. Combo ports
11. Link/Act LED for SFP ports
12. Link/Act LED for Ethernet port
13. Duplex/Collision indicator
14. LAN ports
15. Reset button
16. PoE LED for LAN port
Package Contents
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative for
assistance.
7
1
2
3
4
5
6
1. Terminal blocks: PWR1,
PWR2 (24 36V DC), Relay
-
2. Ground wire.
Installation
Step 1:
Slant the switch and screw the Din-rail kit onto the back of the switch, right in
the middle of the back panel.
Step 2:
Slide the switch onto a DIN-rail from the Din-rail kit and make sure the switch
clicks into the rail firmly.
DIN-rail Installation
Step 1:
Screw the two pieces of wall-mount kits onto both ends of the rear panel of the
switch. A total of six screws are required, as shown below.
Step 2:
Use the switch, with wall mount plates attached, as a guide to mark the
correct locations of the four screws.
Step 3:
Insert a screw head through the large parts of the keyhole-shaped apertures,
and then slide the switch downwards. Tighten the screws for added stability.
Wall-mounting
Q I G
IPS-3082GC-24V
1907-200-P3082GC242-FX011
Reduced Air Flow:
Installation of the equipment in a rack should be such that the
amount of air flow required for safe operation of the equipment is not
compromised.
Mechanical Loading:
Mounting of the equipment in the rack should be such that
a hazardous condition is not achieved due to uneven mechanical loading.
Circuit Overloading:
Consideration should be given to the connection of the equipment
to the supply circuit and the effect that overloading of the circuits might have on
overcurrent protection and supply wiring. Appropriate consideration of equipment
nameplate ratings should be used when addressing this concern.
Network Connection
The switch provides standard Ethernet ports. According to the link type, the switch uses
CAT 3,4,5,5e UTP cables to connect to any other network devices (PCs, servers,
switches,
routers,
or
hubs).
Please
refer
to
the
following
table
for
cable
specifications.
Cable Types and Specifications:
Cable
Type
Max. Length
Connector
10BASE-T
Cat. 3, 4, 5 100-ohm
UTP 100 m (328 ft)
RJ-45
100BASE-TX
Cat. 5 100-ohm UTP
UTP 100 m (328 ft)
RJ-45
1000BASE-T
Cat. 5 / Cat. 5e 100-ohm UTP
UTP 100 m (328 ft)
RJ-45
14
12
13
IPS-3082GC-24V
Version 2.1
Unit =mm (Tolerance ±0.5mm)
*NOTE : This function is available by request only.
15
The product is open type, intended to be installed in and industrial control panel or an
enclosure.
！
Warning [AVERTISSEMENT]
Take into consideration the following guidelines before wiring the device
[Tenez compte des directrices suivantes avant de câbler l’appareil.]
1. Terminal block is mating with Plug and suitable for 12-24AWG.
Torque value 4.5 lb-in.
[Le bornier est compatible avec les connecteurs et convient pour 12-24AWG.
Valeur de couple 4,5 lb-in.]
2. The temperature rating of the input connection cable should higher than 105°C
[La température de service nominale du câble d’entrée doit être supérieure à 105 °C]
3. Use Copper Conductors Only.
[Utilisez uniquement des conducteurs en cuivre.]
* Indoor use and pollution degree II, it must be wiped with a dry cloth for clean up the
device and label.
* Utilisation en intérieur et degré de pollution II, il faut l'essuyer avec un chiffon sec
pour nettoyer l'appareil et son étiquette.
* Do not block air ventilation holes.
* Ne bouchez pas les orifices de ventilation.
* If the equipment is used in a manner not specified by the manufacturer, the
protection provided by the equipment may be impaired.”
* Si l’appareil est utilise d’une maniere non specifiee par le fabricant, la protection
qu’il apporte peut se voir diminuee.”
* Shall be mounted in the Industrial Control Panel and ambient temperature is not
exceed 75 degree C
* doit être monté dans le panneau de commande industriel et la température ambiante
ne doit pas dépasser 75 degrés C
Contents
DIN-rail Kit
CD
IPS-3082GC-24V
Pictures
Number
X 1
X 1
X 1
QIG
Console Cable
X 2
X 1
X 1
Wall-mount Kit
66.0
5
0
.0
2
6
.0
4
3
.0
4
3
.0
4
3
.0
1
1
6
.0
40.0
18.0
107.5
1
5
3
.6
74.3
8
.0
8
0
.5
G2
P1
P3
P5
P1
P3
P2
P4
P6
P8
P7
G1
G1 LINK / ACT
G2
PWR
PWR1
PWR2
Front View
Rear View
1. Din-rail screw holes
2. Wall-mount screw holes
1
2
2
Bottom View
1
2
8
10
9
11
PW
R-1
PW
R-2
1A
@2
4V
DC
12
-4
8V
V2
- V2
+ V1
- V1
+
Fa
ult
Industrial PoE Managed Ethernet
Switch
Industrial PoE Managed Ethernet
Switch
SWITCH
I N D U S T R I A L
PoE
IPS-3082GC
7
5
6
8
P.O.E.
3
1
2
4
16
G2
P1
P3
P5
P1
P3
P2
P4
P6
P8
P7
G1
G1 LINK / ACT
G2
PWR
PWR1
PWR2
IPS-3082GC
7
5
6
8
P.O.E.
3
1
2
4
