
Maintenance-Object Repair Procedures
555-233-143
8-520
Issue 1 May 2002
NPE Crosstalk Test (#6)
The NPE Crosstalk test verifies that this port’s NPE channel talks on the selected
time slot on the TDM bus and never crosses over to time slots reserved for other
connections. If the NPE is not working correctly, 1-way and noisy connections
may be observed. This test is usually only part of a port’s long test sequence and
executes in about 20 to 30 seconds.
Table 8-209.
Test #6 NPE Crosstalk Test
Error
Code
Test
Result
Description / Recommendation
ABORT
Could not allocate the necessary system resources for this test. This could be
due to a failure to seize the port.
1. Retry the command at 1-minute intervals up to 5 times.
1000
ABORT
System resources required to run this test are not available. The port may be
busy with a valid call.
1. Enter display port UUCSSpp to determine the station extension,
attendant number, or trunk group/member number of the port. Enter
status station, status attendant, or status trunk to determine the service
state of the port. If the port is in use, wait until it is idle before testing.
Attendants are always in use (off-hook) if the handset is plugged in and the
port is not busied out.
2. If the port status is active but the port is idle (no calls), check the Error Log
for Error Type 513. The port may be locked up.
3. If the port status is idle, retry the command at 1-minute intervals up to 5
times.
1001
ABORT
Could not allocate the necessary system resources to run this test.
1. Retry the command at 1-minute intervals up to 5 times.
1002
ABORT
The system could not allocate time slots for the test. The system may be under
heavy traffic conditions or it may have time slots out-of- service due to
TDM-BUS errors.
1. If the system has no TDM-BUS errors and is not handling heavy traffic,
retry the command at 1-minute intervals up to 5 times.
1003
ABORT
The system could not allocate a tone receiver for the test. The system may be
oversized for the number of Tone Detectors present, or some Tone Detectors
may be out of service.
1. Resolve any TTR-LEV errors.
2. Resolve any TONE-PT errors.
3. If neither condition exists, retry the command at 1-minute intervals up to 5
times.
Continued on next page
Содержание S8700 Series
