Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 558

Page: 558 / 1817

Flash Registers

www.ti.com

558

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Internal Memory

Table 7-12. FCIM Register Field Descriptions (continued)

Bit

Field

Type

Reset

Description

PMASK

R/W

0x0

Programming Interrupt Mask

This bit controls the reporting of the programming raw interrupt
status to the interrupt controller.

0x0 = The PRIS interrupt is suppressed and not sent to the interrupt
controller.

0x1 = An interrupt is sent to the interrupt controller when the PRIS
bit is set.

AMASK

R/W

0x0

Access Interrupt Mask

This bit controls the reporting of the access raw interrupt status to
the interrupt controller.

0x0 = The ARIS interrupt is suppressed and not sent to the interrupt
controller.

0x1 = An interrupt is sent to the interrupt controller when the ARIS
bit is set.

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SimpleLink Ethernet MSP432E401Y

Reviews:

Related manuals for SimpleLink Ethernet MSP432E401Y

Brands by name

Popular brands

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual

Search results

Summary of Contents for SimpleLink Ethernet MSP432E401Y

Reviews:

Related manuals for SimpleLink Ethernet MSP432E401Y

Brands by name

Popular brands