manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual, Page: 1162 / 1817

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 1162

EPI Registers

www.ti.com

1162

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

External Peripheral Interface (EPI)

Table 16-34. EPIRIS Register Field Descriptions (continued)

Bit

Field

Type

Reset

Description

0

ERRRIS

R

0x0

Error Raw Interrupt Stat

Error Raw Interrupt Status

The error interrupt occurs in the following situations:

• WFIFO Full. For a full WFIFO to generate an error interrupt, the

WFERR bit in the EPIFIFOLVL register must be set.

• Read Stalled. For a stalled read to generate an error interrupt, the

RSERR bit in the EPIFIFOLVL register must be set.

• Timeout. If the MAXWAIT field in the EPIHBnCFG register is

configured to a value other than 0, a timeout error occurs when
XFIFO not-ready signals hold a transaction for more than the
count in the MAXWAIT field.

0x0 = An error has not occurred.

0x1 = A WFIFO Full, a Read Stalled, or a Timeout error has
occurred.

To determine which error occurred, read the status of the EPI Error
Interrupt Status and Clear (EPIEISC) register. This bit is cleared by
writing a 1 to the bit in the EPIEISC register that caused the
interrupt.

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments