manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 1022

EMAC Registers

www.ti.com

1022

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

Ethernet Controller

Table 15-84. EMACDMARIS Register Field Descriptions (continued)

Bit

Field

Type

Reset

Description

25-23

AE

R

0x0

Access Error. This field indicates the type of error that caused a bus
error, for example, error response on the internal bus interface. This
field is valid only when bit[13] (FBI) is set. This field does not
generate an interrupt.

0x0 = Error during RX DMA Write Data Transfer

0x1 = Reserved

0x2 = Reserved

0x3 = Error during TX DMA Read Data Transfer

0x4 = Error during RX DMA Descriptor Write Access

0x5 = Error during TX DMA Descriptor Write Access

0x6 = Error during RX DMA Descriptor Read Access

0x7 = Error during TX DMA Descriptor Read Access

22-20

TS

R

0x0

Transmit Process State. This field indicates the Transmit DMA state.
This field does not generate an interrupt.

0x0 = Stopped; Reset or Stop transmit command processed

0x1 = Running; Fetching transmit transfer descriptor

0x2 = Running; Waiting for status

0x3 = Running; Reading data from host memory buffer and queuing
it to transmit buffer (TX FIFO)

0x4 = Writing Timestamp

0x5 = Reserved

0x6 = Suspended; Transmit descriptor unavailable or transmit buffer
underflow

0x7 = Running; Closing transmit descriptor

19-17

RS

R

0x0

Received Process State. This field indicates the Receive DMA state.
This field does not generate an interrupt.

0x0 = Stopped: Reset or stop receive command issued

0x1 = Running: Fetching receive transfer descriptor

0x2 = Reserved

0x3 = Running: Waiting for receive packet

0x4 = Suspended: Receive descriptor unavailable

0x5 = Running: Closing receive descriptor

0x6 = Writing Timestamp

0x7 = Running: Transferring the receive packet data from receive
buffer to host memory

16

NIS

R/W1C

0x0

Normal Interrupt Summary.

Normal Interrupt Summary bit value is the logical OR of the following
when the corresponding interrupt bits are enabled in EMACDMAIM
register:

•

EMACDMARIS register, bit [0]: Transmit Interrupt

•

EMACDMARIS register, bit[2]: Transmit Buffer
Unavailable

•

EMACDMARIS register, bit[6]: Receive Interrupt

•

EMACDMARIS register, bit[14]: Early Receive
Interrupt

Only unmasked bits (interrupts for which interrupt enable is set in the
EMACDMAIM register) affect the Normal Interrupt Summary bit.

This is a sticky bit and must be cleared (by writing 1 to this bit) each
time a corresponding bit, which causes NIS to be set, is cleared.

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands