Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 980 | Manualshive

Page: 980 / 1817

background image

EMAC Registers

980

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

Ethernet Controller

15.6.26 EMACMMCRXRIS Register (Offset = 0x104) [reset = 0x0]

Ethernet MAC MMC Receive Raw Interrupt Status (EMACMMCRXRIS)

The MAC MMC Receive Interrupt (EMACMMCRXRIS) register maintains the interrupts that are generated
when the following happens:

•

Receive statistic counters reach half of their maximum values (0x80000000 for 32-bit counter and
0x8000 for 16-bit counter).

•

Receive statistic counters cross their maximum values (0xFFFFFFFF for 32-bit counter and 0xFFFF for
16-bit counter).

When the Counter Stop Rollover (CNTSTPRO bit) in the MAC MMC Control (EMACMMCCTRL) register is
set, interrupts are set but the counter remains at all-ones. The EMACMMCRXRIS register is a 32-bit wide
register. An interrupt bit is cleared when the respective MMC counter that caused the interrupt is read. The
least significant byte lane (bits[7:0]) of the respective counter must be read in order to clear the interrupt
bit.

EMACMMCRXRIS is shown in

and described in

.

Return to

Figure 15-41. EMACMMCRXRIS Register

31

30

29

28

27

26

25

24

RESERVED

R-0x0

23

22

21

20

19

18

17

16

RESERVED

UCGF

RESERVED

R-0x0

R-0x0

R-0x0

15

14

13

12

11

10

9

8

RESERVED

R-0x0

7

6

5

4

3

2

1

0

RESERVED

ALGNERR

CRCERR

RESERVED

GBF

R-0x0

R-0x0

R-0x0

R-0x0

R-0x0

Table 15-50. EMACMMCRXRIS Register Field Descriptions

Bit

Field

Type

Reset

Description

31-18

RESERVED

R

0x0

17

UCGF

R

0x0

MMC Receive Unicast Good Frame Counter Interrupt Status.

0x0 = The receive Ethernet MAC Receive Frame Count for Good
Unicast Frames (EMACRXCNTGUNI) register has not reached half
of the maximum value or the maximum value.

0x1 = The receive Ethernet MAC Receive Frame Count for Good
Unicast Frames (EMACRXCNTGUNI) register has reached half of
the maximum value or the maximum value.

16-7

RESERVED

R

0x0

6

ALGNERR

R

0x0

MMC Receive Alignment Error Frame Counter Interrupt Status.

0x0 = The Ethernet MAC Receive Frame Count for Alignment Error
Frames (EMACRXCNTALGNERR) register has not reached half of
the maximum value or the maximum value.

0x1 = The Ethernet MAC Receive Frame Count for Alignment Error
Frames (EMACRXCNTALGNERR) register has reached half of the
maximum value or the maximum value.

«
...
978
979
980
981
982
...
»

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SimpleLink Ethernet MSP432E401Y

Brand: Federal Signal Corporation Pages: 60

Brand: FASTRON. Pages: 16

Brand: Gardner Denver Pages: 22

Brand: National Instruments Pages: 102

Brand: NAU ROBOTICS Pages: 109

Maschine Mikro MK2

Brand: Native Instruments Pages: 181

Brand: Newport Pages: 417

Diaval AF Series

Brand: Comeval Pages: 10

Brand: AirCycler Pages: 2

Torque Converter Lock-Up

Brand: TS Performance Pages: 4

Brand: YASKAWA Pages: 12

Brand: PTZOptics Pages: 4

Brand: Rain Bird Pages: 7

Brand: Dieffematic Pages: 9

Brand: Electric Time Pages: 21

Brand: Nibe Pages: 48

Brand: Parker Pages: 31

Brand: Thevco Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands