manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 1277

www.ti.com

GPTM Registers

1277

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

General-Purpose Timers

18.5.3 GPTMTBMR Register (Offset = 0x8) [reset = 0x0]

GPTM Timer B Mode (GPTMTBMR)

This register configures the GPTM based on the configuration selected in the GPTMCFG register. When
in PWM mode, set the TBAMS bit, clear the TBCMR bit, and configure the TBMR field to 0x1 or 0x2.

This register controls the modes for Timer B when it is used individually. When Timer A and Timer B are
concatenated, this register is ignored and GPTMTAMR controls the modes for both Timer A and Timer B.

NOTE:

Except for the TCACT bit field, all other bits in this register should only be changed when the

TBEN bit in the GPTMCTL register is cleared.

GPTMTBMR is shown in

Figure 18-11

and described in

Table 18-14

.

Return to

Summary Table

.

Figure 18-11. GPTMTBMR Register

31

30

29

28

27

26

25

24

RESERVED

R-0x0

23

22

21

20

19

18

17

16

RESERVED

R-0x0

15

14

13

12

11

10

9

8

TCACT

TBCINTD

TBPLO

TBMRSU

TBPWMIE

TBILD

R/W-0x0

R/W-0x0

R/W-0x0

R/W-0x0

R/W-0x0

R/W-0x0

7

6

5

4

3

2

1

0

TBSNAPS

TBWOT

TBMIE

TBCDIR

TBAMS

TBCMR

TBMR

R/W-0x0

R/W-0x0

R/W-0x0

R/W-0x0

R/W-0x0

R/W-0x0

R/W-0x0

Table 18-14. GPTMTBMR Register Field Descriptions

Bit

Field

Type

Reset

Description

31-16

RESERVED

R

0x0

15-13

TCACT

R/W

0x0

Timer Compare Action Select.

0x0 = Disable compare operations

0x1 = Toggle State on Time-Out

0x2 = Clear CCP on Time-Out

0x3 = Set CCP on Time-Out

0x4 = Set CCP immediately and toggle on Time-Out

0x5 = Clear CCP immediately and toggle on Time-Out

0x6 = Set CCP immediately and clear on Time-Out

0x7 = Clear CCP immediately and set on Time-Out

12

TBCINTD

R/W

0x0

One-Shot/Periodic Interrupt Disable.

0x0 = Time-out interrupt functions normally

0x1 = Time-out interrupt functionality is disabledSetting the
TBCINTD bit in the GPTMTBMR register does not have an effect on
the µDMA or ADC interrupt time-out event trigger assertions. If the
TBTODMAEN bit is set in the GPTMDMAEV register or the
TBTOADCEN bit is set in the GPTMADCEV register, a µDMA or
ADC time-out trigger is sent to the µDMA or ADC, respectively, even
if the TBCINTD bit is set.

11

TBPLO

R/W

0x0

GPTM Timer B PWM Legacy Operation.
This bit is only valid in PWM mode.

0x0 = Legacy operation with CCP pin driven Low when the
GPTMTAILR is reloaded after the timer reaches 0.

0x1 = CCP is driven High when the GPTMTAILR is reloaded after
the timer reaches 0.

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands