manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 240

System Control Registers

www.ti.com

240

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

System Control

Table 4-21. RSCLKCFG Register Field Descriptions (continued)

Bit

Field

Type

Reset

Description

27-24

PLLSRC

R/W

0x0

PLL Source.

This field specifies the PLL input clock source.

0x0 = Reserved

0x3 = MOSC is the PLL input clock source

23-20

OSCSRC

R/W

0x0

Oscillator Source.

This field specifies the oscillator source that becomes the oscillator
clock (OSCCLK) source, which is used when the PLL is bypassed
during run or sleep modes.

0x0 = Reserved

0x1 = Reserved

0x2 = LFIOSC is the oscillator source.

0x3 = MOSC is the oscillator source.

0x4 = Hibernation module RTC oscillator (RTCOSC)

19-10

OSYSDIV

R/W

0x0

Oscillator System Clock Divisor.
This field specifies the system clock divisor value for the oscillator
path. This field is used when the USEPLL bit is 0.
f

syclk

= f

oscclk

/ (O 1)

The divisor value is the OSYSDIV field value + 1

9-0

PSYSDIV

R/W

0x0

PLL System Clock Divisor.
This field specifies the system clock divisor value for the PLL. This
field is used when the USEPLL bit is 1.
f

syclk

= f

VCO

/ (P 1)

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands