Home
/
Texas Instruments
/
SimpleLink Ethernet MSP432E401Y
/
Technical Reference Manual

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual

Share

Page: 1495 / 1817

Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 1495

PWM Registers

1495

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

Pulse Width Modulator (PWM)

21.5.30 PWMnFLTSTAT1 Register [reset = 0x0]

PWM0 Fault Status 1 (PWM0FLTSTAT1), offset 0x808

PWM1 Fault Status 1 (PWM1FLTSTAT1), offset 0x888

PWM2 Fault Status 1 (PWM2FLTSTAT1), offset 0x908

PWM3 Fault Status 1 (PWM3FLTSTAT1), offset 0x988

Along with the PWMnFLTSTAT0 register, this register provides status regarding the fault condition inputs.

If the LATCH bit in the PWMnCTL register is clear, the contents of the PWMnFLTSTAT1 register are read-
only (R) and provide the current state of the digital comparator triggers.

If the LATCH bit in the PWMnCTL register is set, the contents of the PWMnFLTSTAT1 register are read /
write 1 to clear (RW1C) and provide a latched version of the digital comparator triggers. In this mode, the
register bits are cleared by writing a 1 to a set bit. The contents of this register can only be written if the
fault source extensions are enabled (the FLTSRC bit in the PWMnCTL register is set).

NOTE:

The fault status registers, PWMnFLTSTAT0 and PWMnFLTSTAT1, reflect the status of all

fault sources, regardless of what fault sources are enabled for that particular generator.

PWMnFLTSTAT1 is shown in

and described in

Return to

Figure 21-36. PWMnFLTSTAT1 Register

31

30

29

28

27

26

25

24

RESERVED

R-0x0

23

22

21

20

19

18

17

16

RESERVED

R-0x0

15

14

13

12

11

10

9

8

RESERVED

R-0x0

7

6

5

4

3

2

1

0

DCMP7

DCMP6

DCMP5

DCMP4

DCMP3

DCMP2

DCMP1

DCMP0

0x0

0x0

0x0

0x0

0x0

0x0

0x0

0x0

Table 21-32. PWMnFLTSTAT1 Register Field Descriptions

Bit

Field

Type

Reset

Description

31-8

RESERVED

R

0x0

7

DCMP7

0x0

Digital Comparator 7 Trigger.

If the PWMnCTL register LATCH bit is clear, this bit represents the
current state of the Digital Comparator 7 trigger input.

If the PWMnCTL register LATCH bit is set, this bit represents a
sticky version of the trigger.

- If DCMP7 is set, the trigger transitioned to the active state
previously.

- If DCMP7 is clear, the trigger has not transitioned to the active
state since the last time it was cleared.

- The DCMP7 bit is cleared by writing it with the value 1.

«
...
1493
1494
1495
1496
1497
...
»

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands