manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 261

www.ti.com

System Control Registers

261

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

System Control

4.2.27 LDODPCTL Register (Offset = 0x1BC) [reset = 0x12]

LDO Deep-Sleep Power Control (LDODPCTL)

This register specifies the LDO output voltage in sleep mode. This register should be configured while in
run mode. If the VADJEN bit is set, writes can be made to the VLDO field within the provided encodings.
The following table shows the maximum clock frequencies with respect to LDO Voltage.

LDODPCTL is shown in

Figure 4-33

and described in

Table 4-40

.

Return to

Summary Table

.

Figure 4-33. LDODPCTL Register

31

30

29

28

27

26

25

24

VADJEN

RESERVED

R/W-0x0

R-0x0

23

22

21

20

19

18

17

16

RESERVED

R-0x0

15

14

13

12

11

10

9

8

RESERVED

R-0x0

7

6

5

4

3

2

1

0

VLDO

R/W-0x12

Table 4-40. LDODPCTL Register Field Descriptions

Bit

Field

Type

Reset

Description

31

VADJEN

R/W

0x0

Voltage Adjust Enable.

This bit enables the value of the VLDO field to be used to specify the
output voltage of the LDO in deep-sleep mode.

0x0 = The LDO output voltage is set to the factory default value in
deep-sleep mode. The value of the VLDO field does not affect the
LDO operation.

0x1 = The LDO output value in deep-sleep mode is configured by
the value in the VLDO field.

30-8

RESERVED

R

0x0

7-0

VLDO

R/W

0x12

LDO Output Voltage.
This field provides program control of the LDO output voltage in
deep-sleep mode. The value of the field is only used for the LDO
voltage when the VADJEN bit is set.

0x12 = 0.90 V

0x13 = 0.95 V

0x14 = 1.00 V

0x15 = 1.05 V

0x16 = 1.10 V

0x17 = 1.15 V

0x18 = 1.20 V

All other values are reserved.

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands