manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 967

www.ti.com

EMAC Registers

967

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

Ethernet Controller

Table 15-38. EMACRIS Register Field Descriptions (continued)

Bit

Field

Type

Reset

Description

5

MMCRX

R

0x0

MMC Receive Interrupt Status. This bit is cleared when all of the bits
in the Ethernet MAC MMC Receive Interrupt (EMACMMCRXRIS)
register are clear.

0x0 = No interrupts exist in the MAC MMC Receive Interrupt
(EMACMMCTXRIS) register.

0x1 = Indicates an interrupt has been generated in the MAC MMC
Receive Interrupt (EMACMMCRXRIS) register.

4

MMC

R

0x0

MMC Interrupt Status.

0x0 = Indicates the MMC-related Interrupt bits [6:5] in this register
are clear.

0x1 = Indicates that one or more of the MMC-related interrupt bits
[6:5] in this register are set.

3

PMT

R

0x0

PMT Interrupt Status.

0x0 = This bit is cleared when both Bits[6:5] are cleared because of
a read operation to the MAC PMT Control and Status Register
(EMACPMTCTRLSTAT) register.

0x1 = Indicates a Magic packet or Wake-on-LAN frame is received in
the power-down mode (see Bits 5 and 6 in the MACPMTCTRLSTAT
register).

2-0

RESERVED

R

0x0

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands