Home
/
Texas Instruments
/
SimpleLink Ethernet MSP432E401Y
/
Technical Reference Manual

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual

Share

Page: 525 / 1817

Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 525

HIB Registers

525

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

Hibernation Module

6.5.23 HIBTPIO Register (Offset = 0x410) [reset = 0x0]

HIB Tamper I/O Control (HIBTPIO)

The HIB Tamper I/O Control (HIBTPIO) register provides control of the Tamper I/O.

NOTE:

Except for the HIBIO and a portion of the HIBIC register, all other Hibernation module

registers are on the Hibernation module clock domain and have special timing requirements.
Software should make use of the WRC bit in the HIBCTL register to ensure that the required
timing gap has elapsed. If the WRC bit is clear, any attempted write access is ignored. See

. The HIBIO register and bits RSTWK, PADIOWK and WC of the HIBIC register

do not require waiting for write to complete. Because these registers are clocked by the
system clock, writes to these registers/bits are immediate.

Writing to registers other than the HIBCTL and HIBIM before the CLK32EN bit in the HIBCTL
register has been set may produce unexpected results.

NOTE:

Errant writes to the Tamper registers are protected by the Hibernate HIBLOCK register.

HIBTPIO is shown in

and described in

Return to

Figure 6-31. HIBTPIO Register

31

30

29

28

27

26

25

24

RESERVED

GFLTR3

PUEN3

LEV3

EN3

R-0x0

R/W-0x0

R/W-0x0

R/W-0x0

R/W-0x0

23

22

21

20

19

18

17

16

RESERVED

GFLTR2

PUEN2

LEV2

EN2

R-0x0

R/W-0x0

R/W-0x0

R/W-0x0

R/W-0x0

15

14

13

12

11

10

9

8

RESERVED

GFLTR1

PUEN1

LEV1

EN1

R-0x0

R/W-0x0

R/W-0x0

R/W-0x0

R/W-0x0

7

6

5

4

3

2

1

0

RESERVED

GFLTR0

PUEN0

LEV0

EN0

R-0x0

R/W-0x0

R/W-0x0

R/W-0x0

R/W-0x0

Table 6-26. HIBTPIO Register Field Descriptions

Bit

Field

Type

Reset

Description

31-28

RESERVED

R

0x0

27

GFLTR3

R/W

0x0

TMPR3 Glitch Filtering

0x0 = A trigger match level is ignored until the TMPR3 signal is
stable for two hibernate clocks.

0x1 = A trigger match level is ignored until the TMPR3 signal is
stable for 3,071 Hibernate Clocks (93.7ms using 32.768 kHz).

26

PUEN3

R/W

0x0

TMPR3 Internal Weak Pullup Enable

0x0 = Pullup disabled

0x1 = Pullup enabled

25

LEV3

R/W

0x0

TMPR3 Trigger Level

0x0 = Trigger on level low

0x1 = Trigger on level high

24

EN3

R/W

0x0

TMPR3 Enable

0x0 = Detect disabled

0x1 = Detect enabled

23-20

RESERVED

R

0x0

«
...
523
524
525
526
527
...
»

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands