manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 1763

www.ti.com

USB Registers

1763

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

Universal Serial Bus (USB) Controller

27.5.50 USBDMAINTR Register (Offset = 0x200) [reset = 0x0]

USB DMA Interrupt (USBDMAINTR)

OTG A / Host

OTG B / Device

This register provides an interrupt for each USB DMA channel. This interrupt register is cleared when
read. When any bit of this register is set, an interrupt is sent to the interrupt controller. Bits in this register
will only be set if the corresponding enable bit in the DMACTLn register is set.

USBDMAINTR is shown in

Figure 27-61

and described in

Table 27-68

.

Return to

Summary Table

.

Figure 27-61. USBDMAINTR Register

7

6

5

4

3

2

1

0

CH7DMAINT

CH6DMAINT

CH5DMAINT

CH4DMAINT

CH3DMAINT

CH2DMAINT

CH1DMAINT

CH0DMAINT

R/W-0x0

R/W-0x0

R/W-0x0

R/W-0x0

R/W-0x0

R/W-0x0

R/W-0x0

R-0x0

Table 27-68. USBDMAINTR Register Field Descriptions

Bit

Field

Type

Reset

Description

7

CH7DMAINT

R/W

0x0

Channel 7 DMA Interrupt.

0x0 = No effect

0x1 = Channel 7 DMA interrupt enabled.

6

CH6DMAINT

R/W

0x0

Channel 6 DMA Interrupt.

0x0 = No effect

0x1 = Channel 6 DMA interrupt enabled.

5

CH5DMAINT

R/W

0x0

Channel 5 DMA Interrupt.

0x0 = No effect

0x1 = Channel 5 DMA interrupt enabled.

4

CH4DMAINT

R/W

0x0

Channel 4 DMA Interrupt.

0x0 = No effect

0x1 = Channel 4 DMA interrupt enabled.

3

CH3DMAINT

R/W

0x0

Channel 3 DMA Interrupt.

0x0 = No effect

0x1 = Channel 3 DMA interrupt enabled.

2

CH2DMAINT

R/W

0x0

Channel 2 DMA Interrupt.

0x0 = No effect

0x1 = Channel 2 DMA interrupt enabled.

1

CH1DMAINT

R/W

0x0

Channel 1 DMA Interrupt.

0x0 = No effect

0x1 = Channel 1 DMA interrupt enabled.

0

CH0DMAINT

R

0x0

Channel 0 DMA Interrupt.

0x0 = No effect

0x1 = Channel 0 DMA interrupt enabled.

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands