manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 1469

www.ti.com

PWM Registers

1469

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

Pulse Width Modulator (PWM)

Table 21-14. PWMnCTL Register Field Descriptions (continued)

Bit

Field

Type

Reset

Description

9-8

GENBUPD

R/W

0x0

PWMnGENB update mode.

0x0 = ImmediateThe PWMnGENB register value is immediately
updated on a write.

0x1 = Reserved

0x2 = Locally SynchronizedUpdates to the register are reflected to
the generator the next time the counter is 0.

0x3 = Globally SynchronizedUpdates to the register are delayed until
the next time the counter is 0 after a synchronous update has been
requested through the PWMCTL register.

7-6

GENAUPD

R/W

0x0

PWMnGENA update mode.

0x0 = Immediate. The PWMnGENA register value is immediately
updated on a write.

0x1 = Reserved

0x2 = Locally Synchronized. Updates to the register are reflected to
the generator the next time the counter is 0.

0x3 = Globally Synchronized. Updates to the register are delayed
until the next time the counter is 0 after a synchronous update has
been requested through the PWMCTL register.

5

CMPBUPD

R/W

0x0

Comparator B update mode.

0x0 = Locally SynchronizedUpdates to the PWMnCMPB register are
reflected to the generator the next time the counter is 0.

0x1 = Globally SynchronizedUpdates to the register are delayed until
the next time the counter is 0 after a synchronous update has been
requested through the PWMCTL register.

4

CMPAUPD

R/W

0x0

Comparator A update mode.

0x0 = Locally SynchronizedUpdates to the PWMnCMPA register are
reflected to the generator the next time the counter is 0.

0x1 = Globally SynchronizedUpdates to the register are delayed until
the next time the counter is 0 after a synchronous update has been
requested through the PWMCTL register.

3

LOADUPD

R/W

0x0

Load register update mode.

0x0 = Locally SynchronizedUpdates to the PWMnLOAD register are
reflected to the generator the next time the counter is 0.

0x1 = Globally SynchronizedUpdates to the register are delayed until
the next time the counter is 0 after a synchronous update has been
requested through the PWMCTL register.

2

DEBUG

R/W

0x0

Debug mode.

0x0 = The counter stops running when it next reaches 0 and
continues running again when no longer in Debug mode.

0x1 = The counter always runs when in Debug mode.

1

MODE

R/W

0x0

Counter mode.

0x0 = The counter counts down from the load value to 0 and then
wraps back to the load value (Count-Down mode).

0x1 = The counter counts up from 0 to the load value, back down to
0, and then repeats (Count-Up/Down mode).

0

ENABLE

R/W

0x0

PWM block enable. Disabling the PWM by clearing the ENABLE bit
does not clear the COUNT field of the PWMnCOUNT register.
Before re-enabling the PWM (ENABLE = 0x1), the COUNT field
should be cleared by resetting the PWM registers through the
SRPWM register in the System Control Module.

0x0 = The entire PWM generation block is disabled and not clocked.

0x1 = The PWM generation block is enabled and produces PWM
signals.

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands