manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual, Page: 433 / 1817

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 433

www.ti.com

System Control Registers

433

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

System Control

Table 4-194. PCEEPROM Register Field Descriptions

Bit

Field

Type

Reset

Description

31-1

RESERVED

R

0x0

0

P0

R/W

0x1

EEPROM Module 0 Power Control. The Pn bit encodings do not
apply if the corresponding bit in the RCGCEEPROM,
SCGCEEPROM, or DCGCEEPROM register is clear.

0x0 = The EEPROM module is not powered and does not receive a
clock. In this case, the state of the module is not retained. This
configuration provides the lowest power consumption state.

0x1 = The EEPROM module is powered but does not receive a
clock. In this case, the module is inactive.

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments