manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual

The Texas Instruments SimpleLink Ethernet MSP432E401Y offers advanced networking capabilities for embedded applications. For detailed technical information and guidance, download the free Technical Reference Manual from manualshive.com. This comprehensive manual provides in-depth insights into the product's features and functionalities, aiding in successful implementation and development.

Share
Download
background image

GPTM Registers

www.ti.com

1290

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

General-Purpose Timers

18.5.9 GPTMICR Register (Offset = 0x24) [reset = X]

GPTM Interrupt Clear (GPTMICR)

This register is used to clear the status bits in the GPTMRIS and GPTMMIS registers. Writing a 1 to a bit
clears the corresponding bit in the GPTMRIS and GPTMMIS registers.

GPTMICR is shown in

Figure 18-17

and described in

Table 18-20

.

Return to

Summary Table

.

Figure 18-17. GPTMICR Register

31

30

29

28

27

26

25

24

RESERVED

R-0x0

23

22

21

20

19

18

17

16

RESERVED

R-0x0

15

14

13

12

11

10

9

8

RESERVED

DMABINT

RESERVED

TBMCINT

CBECINT

CBMCINT

TBTOCINT

R-X

W1C-0x0

R-0x0

W1C-0x0

W1C-0x0

W1C-0x0

W1C-0x0

7

6

5

4

3

2

1

0

RESERVED

DMAAINT

TAMCINT

RTCCINT

CAECINT

CAMCINT

TATOCINT

R-0x0

W1C-0x0

W1C-0x0

W1C-0x0

W1C-0x0

W1C-0x0

W1C-0x0

Table 18-20. GPTMICR Register Field Descriptions

Bit

Field

Type

Reset

Description

31-14

RESERVED

R

0x0

13

DMABINT

W1C

0x0

GPTM Timer B DMA Done Interrupt Clear.
Writing a 1 to this bit clears the DMABRIS bit in the GPTMRIS
register and the DMABMIS bit in the GPTMMIS register.

12

RESERVED

R

0x0

11

TBMCINT

W1C

0x0

GPTM Timer B Match Interrupt Clear.
Writing a 1 to this bit clears the TBMRIS bit in the GPTMRIS register
and the TBMMIS bit in the GPTMMIS register.

10

CBECINT

W1C

0x0

GPTM Timer B Capture Mode Event Interrupt Clear.
Writing a 1 to this bit clears the CBERIS bit in the GPTMRIS register
and the CBEMIS bit in the GPTMMIS register.

9

CBMCINT

W1C

0x0

GPTM Timer B Capture Mode Match Interrupt Clear.
Writing a 1 to this bit clears the CBMRIS bit in the GPTMRIS register
and the CBMMIS bit in the GPTMMIS register.

8

TBTOCINT

W1C

0x0

GPTM Timer B Time-Out Interrupt Clear.
Writing a 1 to this bit clears the TBTORIS bit in the GPTMRIS
register and the TBTOMIS bit in the GPTMMIS register.

7-6

RESERVED

R

0x0

5

DMAAINT

W1C

0x0

GPTM Timer A DMA Done Interrupt Clear.
Writing a 1 to this bit clears the DMAARIS bit in the GPTMRIS
register and the DMAAMIS bit in the GPTMMIS register.

4

TAMCINT

W1C

0x0

GPTM Timer A Match Interrupt Clear.
Writing a 1 to this bit clears the TAMRIS bit in the GPTMRIS register
and the TAMMIS bit in the GPTMMIS register.

3

RTCCINT

W1C

0x0

GPTM RTC Interrupt Clear.
Writing a 1 to this bit clears the RTCRIS bit in the GPTMRIS register
and the RTCMIS bit in the GPTMMIS register.

2

CAECINT

W1C

0x0

GPTM Timer A Capture Mode Event Interrupt Clear.
Writing a 1 to this bit clears the CAERIS bit in the GPTMRIS register
and the CAEMIS bit in the GPTMMIS register.

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SimpleLink Ethernet MSP432E401Y

Facility Explorer FX Series Installation Instructions preview
FX Series
Brand: Facility Explorer Pages: 4
Bartlett Genesis LT3140 Technical Manual preview
Genesis LT3140
Brand: Bartlett Pages: 5
IBM ServeRAID-MR10is User Manual preview
ServeRAID-MR10is
Brand: IBM Pages: 94
IBM ServeRAID-4 Ultra160 Series Installation Instructions Manual preview
ServeRAID-4 Ultra160 Series
Brand: IBM Pages: 20
IBM 3174 Introduction Manual preview
3174
Brand: IBM Pages: 86
IBM 3745 Series Console Setup Manual preview
3745 Series
Brand: IBM Pages: 205
IBM N6000 Series Installation And Setup Instructions preview
N6000 Series
Brand: IBM Pages: 28
Parker 890CS Product Manual preview
890CS
Brand: Parker Pages: 478
DeLaval MPCII Memo preview
MPCII
Brand: DeLaval Pages: 102
Reer MOSAIC MA2 Quick Installation Manual preview
MOSAIC MA2
Brand: Reer Pages: 2
Sentiotec CV 4 Installation And Operating Instructions Manual preview
CV 4
Brand: Sentiotec Pages: 45
2N 9160341 Installation Manual preview
9160341
Brand: 2N Pages: 107
Allen-Bradley Micro850 series Installation Instructions Manual preview
Micro850 series
Brand: Allen-Bradley Pages: 24
zeeltronic PDCI-NS1V User Manual preview
PDCI-NS1V
Brand: zeeltronic Pages: 15
M-system M8BS2-081 Instruction Manual preview
M8BS2-081
Brand: M-system Pages: 3
Powtran PR5200 Series Manual preview
PR5200 Series
Brand: Powtran Pages: 36
Gantner GAT Access 6600 Series Quick Start Manual preview
GAT Access 6600 Series
Brand: Gantner Pages: 4
Jetter JCM-521 Installation Manual preview
JCM-521
Brand: Jetter Pages: 30

Brands by name

Popular brands

Load more brands