manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 725

www.ti.com

ADC Registers

725

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

Analog-to-Digital Converter (ADC)

10.5.3 ADCIM Register (Offset = 0x8) [reset = 0x0]

ADC Interrupt Mask (ADCIM)

This register controls whether the sample sequencer and digital comparator raw interrupt signals are sent
to the interrupt controller. Each raw interrupt signal can be masked independently.

NOTE:

For a 1 to 2 Msps rate, as the system clock frequency approaches the ADC clock frequency,

it is recommended that the application use the µDMA to store conversion data from the FIFO
to memory before processing rather than an interrupt-driven single data read. Using the
µDMA to store multiple samples before interrupting the processor amortizes interrupt
overhead across multiple transfers and prevents loss of sample data.

NOTE:

Only a single DCONSSn bit should be set at any given time. Setting more than one of these

bits results in the INRDC bit from the ADCRIS register being masked, and no interrupt is
generated on any of the sample sequencer interrupt lines. It is recommended that when
interrupts are used, they are enabled on alternating samples or at the end of the sample
sequence.

ADCIM is shown in

Figure 10-17

and described in

Table 10-10

.

Return to

Summary Table

.

Figure 10-17. ADCIM Register

31

30

29

28

27

26

25

24

RESERVED

R-0x0

23

22

21

20

19

18

17

16

RESERVED

DCONSS3

DCONSS2

DCONSS1

DCONSS0

R-0x0

R/W-0x0

R/W-0x0

R/W-0x0

R/W-0x0

15

14

13

12

11

10

9

8

RESERVED

DMAMASK3

DMAMASK2

DMAMASK1

DMAMASK0

R-0x0

R/W-0x0

R/W-0x0

R/W-0x0

R/W-0x0

7

6

5

4

3

2

1

0

RESERVED

MASK3

MASK2

MASK1

MASK0

R-0x0

R/W-0x0

R/W-0x0

R/W-0x0

R/W-0x0

Table 10-10. ADCIM Register Field Descriptions

Bit

Field

Type

Reset

Description

31-20

RESERVED

R

0x0

19

DCONSS3

R/W

0x0

Digital Comparator Interrupt on SS3.

0x0 = The status of the digital comparators does not affect the SS3
interrupt status.

0x1 = The raw interrupt signal from the digital comparators (INRDC
bit in the ADCRIS register) is sent to the interrupt controller on the
SS3 interrupt line.

18

DCONSS2

R/W

0x0

Digital Comparator Interrupt on SS2.

0x0 = The status of the digital comparators does not affect the SS2
interrupt status.

0x1 = The raw interrupt signal from the digital comparators (INRDC
bit in the ADCRIS register) is sent to the interrupt controller on the
SS2 interrupt line.

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands