Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 470

Page: 470 / 1817

System Exception Registers

www.ti.com

470

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Processor Support and Exception Module

5.2

System Exception Registers

Table 5-1

lists the memory-mapped registers for the processor support and exception module. All register

offset addresses not listed in

Table 5-1

should be considered as reserved locations and the register

contents should not be modified.

Table 5-1. System Exception Registers

Offset

Acronym

Register Name

Section

0x0

SYSEXCRIS

System Exception Raw Interrupt Status

Section 5.2.1

0x4

SYSEXCIM

System Exception Interrupt Mask

Section 5.2.2

0x8

SYSEXCMIS

System Exception Masked Interrupt Status

Section 5.2.3

0xC

SYSEXCIC

System Exception Interrupt Clear

Section 5.2.4

Complex bit access types are encoded to fit into small table cells.

Table 5-2

shows the codes that are

used for access types in this section.

Table 5-2. System Exception Access Type Codes

Access Type

Code

Description

Read Type

Read

Write Type

Write

W1C

1C
W

1 to clear
Write

Reset or Default Value

Value after reset or the default
value

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SimpleLink Ethernet MSP432E401Y

Reviews:

Related manuals for SimpleLink Ethernet MSP432E401Y

Brands by name

Popular brands

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual

Search results

Summary of Contents for SimpleLink Ethernet MSP432E401Y

Reviews:

Related manuals for SimpleLink Ethernet MSP432E401Y

Brands by name

Popular brands