Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 557

Page: 557 / 1817

www.ti.com

Flash Registers

557

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Internal Memory

7.3.5 FCIM Register (Offset = 0x10) [reset = 0x0]

Flash Controller Interrupt Mask (FCIM)

This register controls whether the Flash memory controller generates interrupts to the controller.

FCIM is shown in

Figure 7-13

and described in

Table 7-12

Return to

Summary Table

Figure 7-13. FCIM Register

RESERVED

R-0x0

RESERVED

R-0x0

RESERVED

PROGMASK

RESERVED

ERMASK

INVDMASK

VOLTMASK

RESERVED

R-0x0

R/W-0x0

R-0x0

R/W-0x0

R-0x0

RESERVED

EMASK

PMASK

AMASK

R-0x0

R/W-0x0

Table 7-12. FCIM Register Field Descriptions

Bit

Field

Type

Reset

Description

31-14

RESERVED

0x0

PROGMASK

R/W

0x0

Program Verify Error Interrupt Mask

0x0 = The PROGRIS interrupt is suppressed and not sent to the
interrupt controller.

0x1 = An interrupt is sent to the interrupt controller when the
PROGRIS bit is set.

RESERVED

0x0

ERMASK

R/W

0x0

Erase Verify Error Interrupt Mask

0x0 = The ERRIS interrupt is suppressed and not sent to the
interrupt controller.

0x1 = An interrupt is sent to the interrupt controller when the ERRIS
bit is set.

INVDMASK

R/W

0x0

Invalid Data Interrupt Mask

0x0 = The INVDRIS interrupt is suppressed and not sent to the
interrupt controller.

0x1 = An interrupt is sent to the interrupt controller when the
INVDRIS bit is set.

VOLTMASK

R/W

0x0

Pump Voltage Interrupt Mask

0x0 = The VOLTRIS interrupt is suppressed and not sent to the
interrupt controller.

0x1 = An interrupt is sent to the interrupt controller when the
VOLTRIS bit is set.

8-3

RESERVED

0x0

EMASK

R/W

0x0

EEPROM Interrupt Mask

0x0 = The ERIS interrupt is suppressed and not sent to the interrupt
controller.

0x1 = An interrupt is sent to the interrupt controller when the ERIS
bit is set.

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SimpleLink Ethernet MSP432E401Y

Reviews:

Related manuals for SimpleLink Ethernet MSP432E401Y

Brands by name

Popular brands

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual

Search results

Summary of Contents for SimpleLink Ethernet MSP432E401Y

Reviews:

Related manuals for SimpleLink Ethernet MSP432E401Y

Brands by name

Popular brands