manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 264

System Control Registers

www.ti.com

264

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

System Control

Table 4-42. SDPMST Register Field Descriptions (continued)

Bit

Field

Type

Reset

Description

7

PPDW

R

0x0

PIOSC Power Down Request Warning

0x0 = No error.

0x1 = This bit indicates that the PIOSC was not powered off even
though the PIOSCPD bit was set in the DSLCLKCFG register
because the PIOSC was in use by a peripheral.

6

LMAXERR

R

0x0

VLDO Value Above Maximum Error

0x0 = No error.

0x1 = An error has occurred because software has requested that
the LDO voltage be above the maximum value allowed using the
VLDO bit in the LDOSPCTL, or LDODPCTL register. In this situation,
the LDO is set to the factory default value.

5

RESERVED

R

0x0

4

LSMINERR

R

0x0

VLDO Value Below Minimum Error in Sleep Mode

0x0 = No error.

0x1 = An error has occurred because software has requested that
the LDO voltage be below the minimum value allowed using the
VLDO bit in the LDOSPCTL register. In this situation, the LDO
voltage is not changed when entering sleep mode.

3

LDMINERR

R

0x0

VLDO Value Below Minimum Error in Deep-Sleep Mode

0x0 = No error.

0x1 = An error has occurred because software has requested that
the LDO voltage be below the minimum value allowed using the
VLDO bit in the LDODPCTL register. In this situation, the LDO
voltage is not changed when entering deep-sleep mode.

2

PPDERR

R

0x0

PIOSC Power Down Request Error

0x0 = No error.

0x1 = An error has occurred because software has requested that
the PIOSC be powered down during deep sleep and it is not
possible to power down the PIOSC. In this situation, the PIOSC is
not powered down when entering deep-sleep mode.

1

FPDERR

R

0x0

Flash Memory Power Down Request Error

0x0 = No error.

0x1 = An error has occurred because software has requested a flash
memory power down mode that is not available using the FLASHPM
field in the SLPPWRCFG or the DSLPPWRCFG register.

0

SPDERR

R

0x0

SRAM Power Down Request Error

0x0 = No error.

0x1 = An error has occurred because software has requested an
SRAM power down mode that is not available using the SRAMPM
field in the SLPPWRCFG or the DSLPPWRCFG register.

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands