Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 375

Page: 375 / 1817

www.ti.com

System Control Registers

375

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

System Control

Table 4-142. DCGCGPIO Register Field Descriptions (continued)

Bit

Field

Type

Reset

Description

D10

R/W

0x0

GPIO Port L Deep-Sleep Mode Clock Gating Control

0x0 = GPIO port L is disabled in deep-sleep mode.

0x1 = Enable and provide a clock to GPIO port L in deep-sleep
mode.

R/W

0x0

GPIO Port K Deep-Sleep Mode Clock Gating Control

0x0 = GPIO port K is disabled in deep-sleep mode.

0x1 = Enable and provide a clock to GPIO port K in deep-sleep
mode.

R/W

0x0

GPIO Port J Deep-Sleep Mode Clock Gating Control

0x0 = GPIO port J is disabled in deep-sleep mode.

0x1 = Enable and provide a clock to GPIO port J in deep-sleep
mode.

R/W

0x0

GPIO Port H Deep-Sleep Mode Clock Gating Control

0x0 = GPIO port H is disabled in deep-sleep mode.

0x1 = Enable and provide a clock to GPIO port H in deep-sleep
mode.

R/W

0x0

GPIO Port G Deep-Sleep Mode Clock Gating Control

0x0 = GPIO port G is disabled in deep-sleep mode.

0x1 = Enable and provide a clock to GPIO port G in deep-sleep
mode.

R/W

0x0

GPIO Port F Deep-Sleep Mode Clock Gating Control

0x0 = GPIO port F is disabled in deep-sleep mode.

0x1 = Enable and provide a clock to GPIO port F in deep-sleep
mode.

R/W

0x0

GPIO Port E Deep-Sleep Mode Clock Gating Control

0x0 = GPIO port E is disabled in deep-sleep mode.

0x1 = Enable and provide a clock to GPIO port E in deep-sleep
mode.

R/W

0x0

GPIO Port D Deep-Sleep Mode Clock Gating Control

0x0 = GPIO port D is disabled in deep-sleep mode.

0x1 = Enable and provide a clock to GPIO port D in deep-sleep
mode.

R/W

0x0

GPIO Port C Deep-Sleep Mode Clock Gating Control

0x0 = GPIO port C is disabled in deep-sleep mode.

0x1 = Enable and provide a clock to GPIO port C in deep-sleep
mode.

R/W

0x0

GPIO Port B Deep-Sleep Mode Clock Gating Control

0x0 = GPIO port B is disabled in deep-sleep mode.

0x1 = Enable and provide a clock to GPIO port B in deep-sleep
mode.

R/W

0x0

GPIO Port A Deep-Sleep Mode Clock Gating Control

0x0 = GPIO port A is disabled in deep-sleep mode.

0x1 = Enable and provide a clock to GPIO port A in deep-sleep
mode.

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SimpleLink Ethernet MSP432E401Y

Reviews:

Brands by name

Popular brands

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual

Search results

Summary of Contents for SimpleLink Ethernet MSP432E401Y

Reviews:

Brands by name

Popular brands