manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 1068

MII Management (EPHY) Registers

www.ti.com

1068

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

Ethernet Controller

Table 15-116. EPHYSCR Register Field Descriptions (continued)

Bit

Field

Type

Reset

Description

4

COLFDM

R/W

0x0

Collision in Full-Duplex Mode.

0x0 = Disable collision indication in full-duplex mode. Collision
indication is active in half-duplex mode only.

0x1 = Enable collision signaling in full-duplex mode.

3

RESERVED

R

0x0

2

TINT

R/W

0x0

Test Interrupt. Forces the PHY to generate an interrupt to facilitate
interrupt testing. Interrupts will continue to be generated as long as
this bit remains set.

0x0 = Do not generate interrupt

0x1 = Generate an interrupt

1

INTEN

R/W

0x1

Interrupt Enable. Enables interrupt dependent on the event enables
in the EPHYMISR register (0x012).

0x0 = Disable event based interrupts

0x1 = Enable event based interrupts

0

RESERVED

R

0x0

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands