manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 1741

www.ti.com

USB Registers

1741

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

Universal Serial Bus (USB) Controller

Figure 27-42. USBCSRH0 Register (OTG B / Device)

7

6

5

4

3

2

1

0

RESERVED

FLUSH

R-0x0

R/W-0x0

Table 27-47. USBCSRH0 Register Field Descriptions (OTG B / Device)

Bit

Field

Type

Reset

Description

7-1

RESERVED

R

0x0

0

FLUSH

R/W

0x0

Flush FIFO.
This bit is automatically cleared after the flush is performed.
This bit should only be set when TXRDY is clear and RXRDY is set.
At other times, it may cause data to be corrupted.

0x0 = No effect.

0x1 = Flushes the next packet to be transmitted/read from the
endpoint 0 FIFO. The FIFO pointer is reset and the TXRDY /
RXRDY bit is cleared.

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands