Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 1573

Page: 1573 / 1817

www.ti.com

QEI Registers

1573

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Quadrature Encoder Interface (QEI)

24.5 QEI Registers

Table 24-1

lists the memory-mapped registers for the QEI. All register offset addresses not listed in

Table 24-1

should be considered as reserved locations and the register contents should not be modified.

The offsets are relative to the base address of the QEI module: 0x4002C000.

The QEI module clock must be enabled before the registers can be programmed (see

Section 4.2.100

There must be a delay of 3 system clocks after the QEI module clock is enabled before any QEI module
registers are accessed.

Table 24-1. QEI Registers

Offset

Acronym

Register Name

Section

0x0

QEICTL

QEI Control

Section 24.5.1

0x4

QEISTAT

QEI Status

Section 24.5.2

0x8

QEIPOS

QEI Position

Section 24.5.3

0xC

QEIMAXPOS

QEI Maximum Position

Section 24.5.4

0x10

QEILOAD

QEI Timer Load

Section 24.5.5

0x14

QEITIME

QEI Timer

Section 24.5.6

0x18

QEICOUNT

QEI Velocity Counter

Section 24.5.7

0x1C

QEISPEED

QEI Velocity

Section 24.5.8

0x20

QEIINTEN

QEI Interrupt Enable

Section 24.5.9

0x24

QEIRIS

QEI Raw Interrupt Status

Section 24.5.10

0x28

QEIISC

QEI Interrupt Status and Clear

Section 24.5.11

Complex bit access types are encoded to fit into small table cells.

Table 24-2

shows the codes that are

used for access types in this section.

Table 24-2. QEI Access Type Codes

Access Type

Code

Description

Read Type

Read

Write Type

Write

W1C

1C
W

1 to clear
Write

Reset or Default Value

Value after reset or the default
value

«
...
1571
1572
1573
1574
1575
...
»

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SimpleLink Ethernet MSP432E401Y

Reviews:

Brands by name

Popular brands

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual

Search results

Summary of Contents for SimpleLink Ethernet MSP432E401Y

Reviews:

Brands by name

Popular brands