manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 1475

www.ti.com

PWM Registers

1475

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

Pulse Width Modulator (PWM)

Table 21-17. PWMnISC Register Field Descriptions (continued)

Bit

Field

Type

Reset

Description

2

INTCMPAU

R/W1C

0x0

Comparator A up interrupt. This bit is cleared by writing a 1. Clearing
this bit also clears the INTCMPAU bit in the PWMnRIS register.

0x0 = No interrupt has occurred or the interrupt is masked.

0x1 = The INTCMPAU bits in the PWMnRIS and PWMnINTEN
registers are set, providing an interrupt to the interrupt controller.

1

INTCNTLOAD

R/W1C

0x0

Counter=Load interrupt. This bit is cleared by writing a 1. Clearing
this bit also clears the INTCNTLOAD bit in the PWMnRIS register.

0x0 = No interrupt has occurred or the interrupt is masked.

0x1 = The INTCNTLOAD bits in the PWMnRIS and PWMnINTEN
registers are set, providing an interrupt to the interrupt controller.

0

INTCNTZERO

R/W1C

0x0

Counter=0 interrupt. This bit is cleared by writing a 1. Clearing this
bit also clears the INTCNTZERO bit in the PWMnRIS register.

0x0 = No interrupt has occurred or the interrupt is masked.

0x1 = The INTCNTZERO bits in the PWMnRIS and PWMnINTEN
registers are set, providing an interrupt to the interrupt controller.

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands