manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 508

HIB Registers

www.ti.com

508

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

Hibernation Module

6.5.8 HIBIC Register (Offset = 0x20) [reset = 0x0]

Hibernation Interrupt Clear (HIBIC)

This register is the interrupt write-one-to-clear register for the Hibernation module interrupt sources.
Writing a 1 to a bit clears the corresponding interrupt in the HIBRIS register.

NOTE:

Writes to the RSTWK, PADIOWK and WC bits of this register are immediate and the status

may be read from the HIBRIS and HIBMIS registers without monitoring the WRC bit of the
HIBCTL register.

NOTE:

All I/O wake sources are cleared by a write to either or both the RSTWK and PADIOWK bits.

This clears the source of interrupts for RSTWK, PADIOWK and the GPIOWAKESTAT
register.

HIBIC is shown in

Figure 6-16

and described in

Table 6-11

.

Return to

Summary Table

.

Figure 6-16. HIBIC Register

31

30

29

28

27

26

25

24

RESERVED

R-0x0

23

22

21

20

19

18

17

16

RESERVED

R-0x0

15

14

13

12

11

10

9

8

RESERVED

R-0x0

7

6

5

4

3

2

1

0

VDDFAIL

RSTWK

PADIOWK

WC

EXTW

LOWBAT

RESERVED

RTCALT0

R/W1C-0x0

R/W1C-0x0

R/W1C-0x0

R/W1C-0x0

R/W1C-0x0

R/W1C-0x0

R-0x0

R/W1C-0x0

Table 6-11. HIBIC Register Field Descriptions

Bit

Field

Type

Reset

Description

31-8

RESERVED

R

0x0

7

VDDFAIL

R/W1C

0x0

VDD Fail Interrupt Clear
Writing a 1 to this bit clears the VDDFAIL bit in the HIBRIS and
HIBMIS registers.
Reads return the raw interrupt status.

6

RSTWK

R/W1C

0x0

Reset Pad I/O Wake-Up Interrupt Clear Writing a 1 to this bit clears
the RSTWK bit in the HIBRIS and HIBMIS registers.
Reads return the raw interrupt status.

5

PADIOWK

R/W1C

0x0

Pad I/O Wake-Up Interrupt Clear Writing a 1 to this bit clears the
PADIOWK bit in the HIBRIS and HIBMIS registers.
Reads return the raw interrupt status.

4

WC

R/W1C

0x0

Write Complete/Capable Interrupt Clear
Writing a 1 to this bit clears the WC bit in the HIBRIS and HIBMIS
registers.
Reads return the raw interrupt status.

3

EXTW

R/W1C

0x0

External Wake-Up Interrupt Clear
Writing a 1 to this bit clears the EXTW bit in the HIBRIS and HIBMIS
registers.
Reads return the raw interrupt status.

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands