manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 560

Flash Registers

www.ti.com

560

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

Internal Memory

Table 7-13. FCMISC Register Field Descriptions (continued)

Bit

Field

Type

Reset

Description

2

EMISC

R/W1C

0x0

EEPROM Masked Interrupt Status and Clear

0x0 = When read, a 0 indicates that an interrupt has not occurred.A
write of 0 has no effect on the state of this bit.

0x1 = When read, a 1 indicates that an unmasked interrupt was
signaled.Writing a 1 to this bit clears EMISC and also the ERIS bit in
the FCRIS register (see ).

1

PMISC

R/W1C

0x0

Programming Masked Interrupt Status and Clear

0x0 = When read, a 0 indicates that a programming cycle complete
interrupt has not occurred.A write of 0 has no effect on the state of
this bit.

0x1 = When read, a 1 indicates that an unmasked interrupt was
signaled because a programming cycle completed.Writing a 1 to this
bit clears PMISC and also the PRIS bit in the FCRIS register (see ).

0

AMISC

R/W1C

0x0

Access Masked Interrupt Status and Clear

0x0 = When read, a 0 indicates that no improper accesses have
occurred.A write of 0 has no effect on the state of this bit.

0x1 = When read, a 1 indicates that an unmasked interrupt was
signaled because a program or erase action was attempted on a
block of Flash memory that contradicts the protection policy for that
block as set in the FMPPEn registers.Writing a 1 to this bit clears
AMISC and also the ARIS bit in the FCRIS register (see ).

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands