manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 1308

GPTM Registers

www.ti.com

1308

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

General-Purpose Timers

Table 18-36. GPTMDMAEV Register Field Descriptions (continued)

Bit

Field

Type

Reset

Description

2

CAEDMAEN

R/W

0x0

GPTM A Capture Event DMA Trigger Enable.
When this bit is enabled, a Timer A dma_req signal is sent to the
µDMA when a capture event has occurred.

0x0 = Timer A Capture Event DMA trigger is disabled.

0x1 = Timer A Capture Event DMA trigger is enabled.

1

CAMDMAEN

R/W

0x0

GPTM A Capture Match Event DMA Trigger Enable.
When this bit is enabled, a Timer A dma_req signal is sent to the
µDMA when a capture match event has occurred.

0x0 = Timer A Capture Match DMA trigger is disabled.

0x1 = Timer A Capture Match DMA trigger is enabled.

0

TATODMAEN

R/W

0x0

GPTM A Time-Out Event DMA Trigger Enable.
When this bit is enabled, a Timer A dma_req signal is sent to the
µDMA on a time-out event.

0x0 = Timer A Time-Out DMA trigger is disabled.

0x1 = Timer A Time-Out DMA trigger is enabled.

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands