manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 1307

www.ti.com

GPTM Registers

1307

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

General-Purpose Timers

18.5.25 GPTMDMAEV Register (Offset = 0x6C) [reset = 0x0]

GPTM DMA Event (GPTMDMAEV)

This register allows software to enable/disable GPTM DMA trigger events. Setting a bit enables the
corresponding DMA trigger, while clearing a bit disables it.

GPTMDMAEV is shown in

Figure 18-33

and described in

Table 18-36

.

Return to

Summary Table

.

Figure 18-33. GPTMDMAEV Register

31

30

29

28

27

26

25

24

RESERVED

R-0x0

23

22

21

20

19

18

17

16

RESERVED

R-0x0

15

14

13

12

11

10

9

8

RESERVED

TBMDMAEN

CBEDMAEN

CBMDMAEN

TBTODMAEN

R-0x0

R/W-0x0

R/W-0x0

R/W-0x0

R/W-0x0

7

6

5

4

3

2

1

0

RESERVED

TAMDMAEN

RTCDMAEN

CAEDMAEN

CAMDMAEN

TATODMAEN

R-0x0

R/W-0x0

R/W-0x0

R/W-0x0

R/W-0x0

R/W-0x0

Table 18-36. GPTMDMAEV Register Field Descriptions

Bit

Field

Type

Reset

Description

31-12

RESERVED

R

0x0

11

TBMDMAEN

R/W

0x0

GPTM B Mode Match Event DMA Trigger Enable.
When this bit is enabled, a Timer B dma_req signal is sent to the
µDMA when a mode match has occurred.

0x0 = Timer B Mode Match DMA trigger is disabled.

0x1 = Timer B DMA Mode Match trigger is enabled.

10

CBEDMAEN

R/W

0x0

GPTM B Capture Event DMA Trigger Enable.
When this bit is enabled, a Timer B dma_req signal is sent to the
µDMA when a capture event has occurred.

0x0 = Timer B Capture Event DMA trigger is disabled.

0x1 = Timer B Capture Event DMA trigger is enabled.

9

CBMDMAEN

R/W

0x0

GPTM B Capture Match Event DMA Trigger Enable.
When this bit is enabled, a Timer B dma_req signal is sent to the
µDMA when a capture match event has occurred.

0x0 = Timer B Capture Match DMA trigger is disabled.

0x1 = Timer B Capture Match DMA trigger is enabled.

8

TBTODMAEN

R/W

0x0

GPTM B Time-Out Event DMA Trigger Enable.
When this bit is enabled, a Timer B dma_req signal is sent to the
µDMA on a time-out event.

0x0 = Timer B Time-Out DMA trigger is disabled.

0x1 = Timer B Time-Out DMA trigger is enabled.

7-5

RESERVED

R

0x0

4

TAMDMAEN

R/W

0x0

GPTM A Mode Match Event DMA Trigger Enable.
When this bit is enabled, a Timer A dma_req signal is sent to the
µDMA when a mode match has occurred.

0x0 = Timer A Mode Match DMA trigger is disabled.

0x1 = Timer A DMA Mode Match trigger is enabled.

3

RTCDMAEN

R/W

0x0

GPTM A RTC Match Event DMA Trigger Enable.
When this bit is enabled, a Timer A dma_req signal is sent to the
µDMA when a RTC match has occurred.

0x0 = Timer A RTC Match DMA trigger is disabled.

0x1 = Timer A RTC Match DMA trigger is enabled.

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands