manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual, Page: 1803 / 1817

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 1803

www.ti.com

WDT Registers

1803

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

Watchdog Timers

28.5.3 WDTCTL Register (Offset = 0x8)

Watchdog Control (WDTCTL)

WDT0, reset = 0x0000.0000

WDT1, reset = 0x8000.0000

This register is the watchdog control register. The watchdog timer can be configured to generate a reset
signal (on second time-out) or an interrupt on time-out.

When the watchdog interrupt has been enabled by setting the INTEN bit, all subsequent writes to the
INTEN bit are ignored. The only mechanisms that can re-enable writes to this bit are a hardware reset or a
software reset initiated by setting the appropriate bit in the Watchdog Timer Software Reset (SRWD)
register.

NOTE:

Because the Watchdog Timer 1 module has an independent clocking domain, its registers

must be written with a timing gap between accesses. Software must guarantee that this
delay is inserted between back-to-back writes to WDT1 registers or between a write followed
by a read to the registers. The timing for back-to-back reads from the WDT1 module has no
restrictions. The WRC bit in the Watchdog Control (WDTCTL) register for WDT1 indicates
that the required timing gap has elapsed. This bit is cleared on a write operation and set
once the write completes, indicating to software that another write or read may be started
safely. Software should poll WDTCTL for WRC =1 prior to accessing another register. Note
that WDT0 does not have this restriction as it runs off the system clock and therefore does
not have a WRC bit.

WDTCTL is shown in

Figure 28-4

and described in

Table 28-5

.

Return to

Summary Table

.

Figure 28-4. WDTCTL Register

31

30

29

28

27

26

25

24

WRC

RESERVED

R-0x1

R-0x0

23

22

21

20

19

18

17

16

RESERVED

R-0x0

15

14

13

12

11

10

9

8

RESERVED

R-0x0

7

6

5

4

3

2

1

0

RESERVED

INTTYPE

RESEN

INTEN

R-0x0

R/W-0x0

R/W-0x0

R/W-0x0

Table 28-5. WDTCTL Register Field Descriptions

Bit

Field

Type

Reset

Description

31

WRC

R

0x0

Write Complete.
This bit is RESERVED for WDT0 and has a reset value of 0.

0x0 = A write access to one of the WDT1 registers is in progress.

0x1 = A write access is not in progress, and WDT1 registers can be
read or written.

30-3

RESERVED

R

0x0

2

INTTYPE

R/W

0x0

Watchdog Interrupt Type

0x0 = Watchdog interrupt is a standard interrupt.

0x1 = Watchdog interrupt is a non-maskable interrupt.

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments