manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Technical Reference Manual

Share
Download
Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 327

www.ti.com

System Control Registers

327

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

System Control

Table 4-100. RCGCGPIO Register Field Descriptions (continued)

Bit

Field

Type

Reset

Description

8

R8

R/W

0x0

GPIO Port J Run Mode Clock Gating Control

0x0 = GPIO port J is disabled.

0x1 = Enable and provide a clock to GPIO port J in run mode.

7

R7

R/W

0x0

GPIO Port H Run Mode Clock Gating Control

0x0 = GPIO port H is disabled.

0x1 = Enable and provide a clock to GPIO port H in run mode.

6

R6

R/W

0x0

GPIO Port G Run Mode Clock Gating Control

0x0 = GPIO port G is disabled.

0x1 = Enable and provide a clock to GPIO port G in run mode.

5

R5

R/W

0x0

GPIO Port F Run Mode Clock Gating Control

0x0 = GPIO port F is disabled.

0x1 = Enable and provide a clock to GPIO port F in run mode.

4

R4

R/W

0x0

GPIO Port E Run Mode Clock Gating Control

0x0 = GPIO port E is disabled.

0x1 = Enable and provide a clock to GPIO port E in run mode.

3

R3

R/W

0x0

GPIO Port D Run Mode Clock Gating Control

0x0 = GPIO port D is disabled.

0x1 = Enable and provide a clock to GPIO port D in run mode.

2

R2

R/W

0x0

GPIO Port C Run Mode Clock Gating Control

0x0 = GPIO port C is disabled.

0x1 = Enable and provide a clock to GPIO port C in run mode.

1

R1

R/W

0x0

GPIO Port B Run Mode Clock Gating Control

0x0 = GPIO port B is disabled.

0x1 = Enable and provide a clock to GPIO port B in run mode.

0

R0

R/W

0x0

GPIO Port A Run Mode Clock Gating Control

0x0 = GPIO port A is disabled.

0x1 = Enable and provide a clock to GPIO port A in run mode.

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands