Texas Instruments SimpleLink Ethernet MSP432E401Y Technical Reference Manual Download Page 1172 | Manualshive

Page: 1172 / 1817

background image

EPI Registers

1172

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

External Peripheral Interface (EPI)

16.5.27 EPIHB16CFG4 Register (Offset = 0x30C) [reset = 0x00080000]

EPI Host-Bus 16 Configuration 4 (EPIHB16CFG4)

NOTE:

The MODE field in the EPICFG register determines which configuration is enabled.

For EPIHB16CFG4 to be valid, the MODE field must be 0x3.

EPIHB16CFG4 is shown in

and described in

Return to

Figure 16-56. EPIHB16CFG4 Register

31

30

29

28

27

26

25

24

RESERVED

R-0x0

23

22

21

20

19

18

17

16

RESERVED

WRHIGH

RDHIGH

ALEHIGH

WRCRE

RDCRE

BURST

R-0x0

R/W-0x0

R/W-0x0

R/W-0x1

R/W-0x0

R/W-0x0

R/W-0x0

15

14

13

12

11

10

9

8

RESERVED

R-0x0

7

6

5

4

3

2

1

0

WRWS

RDWS

RESERVED

MODE

R/W-0x0

R/W-0x0

R-0x0

R/W-0x0

Table 16-40. EPIHB16CFG4 Register Field Descriptions

Bit

Field

Type

Reset

Description

31-22

RESERVED

R

0x0

21

WRHIGH

R/W

0x0

CS3n WRITE Strobe Polarity. This field is used if the CSBAUD bit is
enabled in EPIHB16CFG2.

0x0 = The WRITE strobe for CS3n accesses is WRn (active Low).

0x1 = The WRITE strobe for CS3n accesses is WR (active High).

20

RDHIGH

R/W

0x0

CS3n READ Strobe Polarity. This field is used if the CSBAUD bit is
enabled in EPIHB16CFG2.

0x0 = The READ strobe for CS3n accesses is RDn (active Low).

0x1 = The READ strobe for CS3n accesses is RD (active High).

19

ALEHIGH

R/W

0x1

CS3n ALE Strobe Polarity This field is used if the CSBAUD bit is
enabled in EPIHB16CFG2.

0x0 = The address latch strobe for CS3n accesses is ADVn (active
Low).

0x1 = The address latch strobe for CS3n accesses is ALE (active
High).

18

WRCRE

R/W

0x0

CS3n PSRAM Configuration Register Write. Used for PSRAM
configuration registers.
With WRCRE set, the next transaction by the EPI will be a write of
the CR bit field in the EPIHBPSRAM register to the configuration
register (CR) of the PSRAM.
The WRCRE bit will self clear once the write-enabled CRE access is
complete.

0x0 = No Action.

0x1 = Start CRE write transaction for CS3n.

«
...
1170
1171
1172
1173
1174
...
»

Summary of Contents for SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SimpleLink Ethernet MSP432E401Y

Brand: Vacon Pages: 64

UTAdvanced UT35A

Brand: YOKOGAWA Pages: 18

Brand: Newport Pages: 417

Brand: Partizan Pages: 7

Brand: Zaiput Flow Technologies Pages: 10

VLTAutomationDrive FC 360

Brand: Danfoss Pages: 52

Brand: J+J Pages: 6

Brand: Eaton Pages: 2

Brand: PI Pages: 111

total control MRX-10

Brand: Universal Remote Control Pages: 16

Brand: DIG Pages: 16

Brand: Omron Pages: 510

Brand: Instruments of Things Pages: 12

Brand: Walchem Pages: 88

Brand: GRAUPNER Pages: 76

ADAP-KOOL AK-PC 572

Brand: Danfoss Pages: 28

Meridian MEC-110

Brand: FASTRON. Pages: 12

aFLAT CRTtoLCD-71

Brand: eCOUNT Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands